Thickness planer maintenance and specifications: Difference between revisions
Jump to navigation
Jump to search
No edit summary |
Aspontarelli (talk | contribs) |
||
| (15 intermediate revisions by the same user not shown) | |||
| Line 16: | Line 16: | ||
= General = | = General = | ||
Invicta DGI-63D | |||
= Reference = | = Reference = | ||
Manual: https:// | Planer Manual: [[Media:Invicta Rockwell DGI-63D Thicknesser Manual.pdf|https://vector-space.org/wiki/File:Invicta_Rockwell_DGI-63D_Thicknesser_Manual.pdf]] | ||
= Maintenance = | = Maintenance = | ||
| Line 56: | Line 51: | ||
= List of Specifications = | = List of Specifications = | ||
[[File:DGI-63D_motor_plate.jpg|400px|thumb|right|DGI-63D motor nameplate]] | |||
* | * Cutter Insert Size: 14 x 14 x 2mm | ||
* '''AMPS''' | ** Insert Screws: T20 x M6-1.0 x 15mm. Head height = 2mm. head angle = 100deg. 90 degree feels alright but could cause catastrophic failure. | ||
* '''AMPS''' 32.8 AMP | |||
* '''DEPTH CAPACITY''' 6 IN | * '''DEPTH CAPACITY''' 6 IN | ||
* '''MAX DEPTH OF CUT''' 1/8 IN | * '''MAX DEPTH OF CUT''' 1/8 IN | ||
* '''NO LOAD SPEED''' 4,500 (CUTTERHEAD) RPM | * '''NO LOAD SPEED''' 4,500 (CUTTERHEAD) RPM | ||
* '''Dust Chute Diameter (in.)''' 4 | * '''Dust Chute Diameter (in.)''' 4 | ||
* '''Motor''' TEFC, 12.5HP, 3Ph, 230V . Note that the actual motor (12.5HP) does not match that described in the manual (10HP). | |||
* '''Motor''' TEFC, | |||
'''END OF THE PROCEDURE''' | '''END OF THE PROCEDURE''' | ||
Latest revision as of 10:53, 8 May 2025
|
Shop Area: Woodshop Tool: Thickness Planer |
Procedure Number MT 110-02, Rev. 1 |
Date 1/22/2021 |
General
Invicta DGI-63D
Reference
Planer Manual: https://vector-space.org/wiki/File:Invicta_Rockwell_DGI-63D_Thicknesser_Manual.pdf
Maintenance
Periodic Maintenance
- Routinely check the tool for damage or broken parts.
- Clean the top cover, dust shroud and all accessible areas of the unit of dust and wood debris that have collected in from planeing.
- Wipe off infeed and outfeed rollers.
- Clean base table. Light waxing will help wood material pass through the planer.
- Evaluate blade sharpness condition. Replace as necessary.
- Gauge Calibration, check thickness gauge calibration and turret stop calibration.
- Check brushes for wear and replace as necessary
- The lubricant in the gear box must be drained and replaced every 2,500 hours. Multi-purpose gear box lubricant will be suitable.
To Change Planer Inserts
- Use 10mm socket to remove four screws holding top cover
- Use T27 to remove damaged insert
- Clean mating surface
- Install new insert to 45 in-lb torque
- Reinstall top cover
List of Specifications
- Cutter Insert Size: 14 x 14 x 2mm
- Insert Screws: T20 x M6-1.0 x 15mm. Head height = 2mm. head angle = 100deg. 90 degree feels alright but could cause catastrophic failure.
- AMPS 32.8 AMP
- DEPTH CAPACITY 6 IN
- MAX DEPTH OF CUT 1/8 IN
- NO LOAD SPEED 4,500 (CUTTERHEAD) RPM
- Dust Chute Diameter (in.) 4
- Motor TEFC, 12.5HP, 3Ph, 230V . Note that the actual motor (12.5HP) does not match that described in the manual (10HP).
END OF THE PROCEDURE