Cnc plasma maintenance and specifications: Difference between revisions

From vector-space.org
Jump to navigation Jump to search

Aspontarelli (talk | contribs)

4 user groups
817 edits
VisualWikitext
Created page with "{| |width="33%"| '''Shop Area:''' Metal Shop '''Tool:''' CNC Plasma Cutter '''Requires in-person training:''' Yes  |width="33%"| '''Procedure Number''' MT 130-05, Rev. 0..."
 
 
(5 intermediate revisions by 2 users not shown)
Line 9: Line 9:
'''Procedure Number'''
'''Procedure Number'''


MT 130-05, Rev. 0
MT 130-05, Rev. 1
|width="33%"|
|width="33%"|
'''Date'''
'''Date'''


DRAFT
2/8/2021
|}
|}


= General =
= General =
We run a Lotos LTP5500 plasma cutter on the Langmuir Crossfire CNC plasma table.


[http://www.langmuirsystems.com/crossfire Langmuir Crossfire CNC Plasma Table]. 
[http://www.langmuirsystems.com/crossfire Langmuir Crossfire CNC Plasma Table]. 


[http://www.razorweld.com/catalogue_product.asp?product=983&category=22&subcategory=87 Razorweld plasma cutter].


 
 
[[File:CNC Plasma Cutter.png]] 


= Reference =
= Reference =
Line 29: Line 30:
* https://www.langmuirsystems.com/crossfire/legacy
* https://www.langmuirsystems.com/crossfire/legacy
* https://unimig.com.au/wp-content/uploads/2019/08/RAZOR-CUT-45-Manual.pdf
* https://unimig.com.au/wp-content/uploads/2019/08/RAZOR-CUT-45-Manual.pdf
* Lotus LTP5500D Plasma source, https://www.uwelding.com/lotos-ltp5500d-cnc-plasma-cutter-non-touch-pilot-arc-cnc-enabled-plasma-cutter-digital-control-thc-torch-height-control-dual-voltage-110v-220v-3-5-inch-clean-cut-brown-55amp-cnc/


= Maintenance =
= Maintenance =
'''Razorcut 45 Plasma Cutter'''


Exposure to extremely dusty, damp, or corrosive air is damaging to the welding/cutting machine. In order to prevent any possible failure or fault of this welding/ cutting equipment, clean the dust at regular intervals with clean and dry compressed air of required pressure.
Exposure to extremely dusty, damp, or corrosive air is damaging to the welding/cutting machine. In order to prevent any possible failure or fault of this welding/ cutting equipment, clean the dust at regular intervals with clean and dry compressed air of required pressure.
Line 38: Line 38:
= Specifications =
= Specifications =


These are a few of the important details in regards to the Razorcut 45 Plasma Cutter.
'''Technical Data'''
Power Supply / Phases (V-Ph) 230v - 1 +/- 15%
Duty Cycle @ 104°F 30% @ 45Amps
Rated Power (KVA) 5.50
Output Current Range (A) Plasma 20-40
Rated Output Voltage (V) 96
Efficiency (%) 90
Insulation Class H
Protection Class IP21S
Plasma Arc Starting Piolt L/F
Air Flow Pressure (MPA) 0.5 (75 psi)
Air Flow Rate (CFM) 6.70
Cutting Thickness - Clean (Inch) 5/8
Cutting Thickness - Severance (Inch) 25/32
Dimensions (inch) 18.1" x 6.69" x 12.99"
Weight (Pounds) 20.2
'''Torch Type:''' TRF-45-6-CC1 Plasma torch
'''Kerf:''' The tip orifices focus the plasma stream to the work piece. It is important to use the correct size tip for the amperage being used, for example a tip with a 3/64" orifice is good for 0-40 amps whereas a 1/16" orifice is better for 40-80 amps
'''Air Pressure and Volume:''' The RazorCut45 air pressure is pre-set at 4.5 psi and requires a flow rate of 6.0 CF/M.


'''CROSSFIRE™ SPECIFICATIONS'''
'''Langmuir Crossfire'''


* Cutting Envelope Dimensions:25.3” (X) x 23.3” (Y) x 3.0" (Z)
* Cutting Envelope Dimensions:25.3” (X) x 23.3” (Y) x 3.0" (Z)
Line 92: Line 53:
* Table Surface: Replaceable Steel Slats, 50mm wide x 3mm thick
* Table Surface: Replaceable Steel Slats, 50mm wide x 3mm thick
* Input Power: 110/220 VAC (selectable)
* Input Power: 110/220 VAC (selectable)
* Plasma Source: Lotus LTP5500D


 
 


'''THIS IS THE END OF THE PROCEDURE'''
                                                      '''END OF THE PROCEDURE'''

Latest revision as of 11:58, 15 March 2022

Shop Area: Metal Shop

Tool: CNC Plasma Cutter

Requires in-person training: Yes 

Procedure Number

MT 130-05, Rev. 1

Date

2/8/2021

General

We run a Lotos LTP5500 plasma cutter on the Langmuir Crossfire CNC plasma table.

Langmuir Crossfire CNC Plasma Table. 


 

Reference

Maintenance

Exposure to extremely dusty, damp, or corrosive air is damaging to the welding/cutting machine. In order to prevent any possible failure or fault of this welding/ cutting equipment, clean the dust at regular intervals with clean and dry compressed air of required pressure.

Specifications

Langmuir Crossfire

  • Cutting Envelope Dimensions:25.3” (X) x 23.3” (Y) x 3.0" (Z)
  • Machine Weight:130 Pounds
  • Linear Bearing Type: Ball Bearing Carriages on Zinc-plated Steel Tube Rails
  • Stepper Motor Size: X-Axis 284 oz-in Y-Axis 425 oz-in
  • PC Interface: Windows USB
  • Mechanical Drive System:3/8”-8 4-Start ACME Lead Screws and Acetal Anti-Backlash Lead Nuts
  • Motion Accuracy:0.002” per 12” inches
  • Step Resolution:0.0005”
  • Maximum Cut Speed:300 ipm
  • Torch Height Control: Manual Torch Height Adjustment
  • Table Surface: Replaceable Steel Slats, 50mm wide x 3mm thick
  • Input Power: 110/220 VAC (selectable)
  • Plasma Source: Lotus LTP5500D

  

                                                      END OF THE PROCEDURE
Retrieved from "https://vector-space.org/wiki/index.php?title=Cnc_plasma_maintenance_and_specifications&oldid=1257"