Plasma cutter maintenance and specifications: Difference between revisions
Aspontarelli (talk | contribs) (Created page with "{| |width="33%"| '''Shop Area:''' Metal Shop '''Tool:''' Plasma Cutter (handheld) <span style="color:#FFFFFF;">'''<span style="background-color:#FF0000;">Requires in-person...") |
Aspontarelli (talk | contribs) |
||
| (10 intermediate revisions by the same user not shown) | |||
| Line 7: | Line 7: | ||
<span style="color:#FFFFFF;">'''<span style="background-color:#FF0000;">Requires in-person training:</span>'''<span style="background-color:#FF0000;"> Yes </span></span> | <span style="color:#FFFFFF;">'''<span style="background-color:#FF0000;">Requires in-person training:</span>'''<span style="background-color:#FF0000;"> Yes </span></span> | ||
'''Procedure Number''': | '''Procedure Number''': MT 110-03, Rev. 1 | ||
'''Last Revision:''' 4/30/2021 | '''Last Revision:''' 4/30/2021 | ||
| Line 18: | Line 18: | ||
The RazorCut 45 plasma cutter is used for making curved cuts in metal. It can cut up to 5/8" thick steel and 1/4" aluminum. | The RazorCut 45 plasma cutter is used for making curved cuts in metal. It can cut up to 5/8" thick steel and 1/4" aluminum. | ||
= REFERENCE = | = REFERENCE = | ||
Razor Cut 45 product page (http://razorweld.com/catalogue_product.asp?product=983&category=22&subcategory=87) | * Razor Cut 45 product page (http://razorweld.com/catalogue_product.asp?product=983&category=22&subcategory=87) | ||
* [[:File:RAZOR-CUT-45-Manual.pdf|Razor Cut 45 operating manual]] | |||
* [[:File:Cutmaster82_OperatingManual.pdf|Cutmaster 82 Operating Manual]] | |||
* [[:File:Cutmaster82_ServiceManual.pdf|Cutmaster 82 Service Manual]] | |||
= | = MAINTENANCE = | ||
= LIST OF SPECIFICATIONS = | |||
The RazorCut 45 is retrofit with a genuine IPT 60 torch. | The RazorCut 45 is retrofit with a genuine IPT 60 torch. | ||
Recommended tip orifice sizes: | |||
20 amp tip - 0.6mm/.025" - 15 to 20 amps - 50 to 55 psi | |||
30 amp tip - 0.8mm/.030" - 21 to 30 amps - 55 to 60 psi | |||
40 amp tip - 0.9mm/.035" - 31 to 40 amps - 65 to 70 psi | |||
50 amp tip - 1.0mm/.040" - 41 to 50 amps - 65 to 75 psi | |||
60 amp tip - 1.1mm/.044" - 51 to 60 amps - 65 to 75 psi | |||
70 amp tip - 1.2mm/.047" - 61 to 70 amps - 75 to 80 psi | |||
80 amp tip - 1.3mm/.051" - 71 to 80 amps - 75 to 80 psi | |||
These are a few of the important details in regards to the Razorcut 45 Plasma Cutter. | |||
'''Technical Data''' | |||
Power Supply / Phases (V-Ph) 230v - 1 +/- 15% | |||
Duty Cycle @ 104°F 30% @ 45Amps | |||
Rated Power (KVA) 5.50 | |||
Output Current Range (A) Plasma 20-40 | |||
Rated Output Voltage (V) 96 | |||
Efficiency (%) 90 | |||
Insulation Class H | |||
Protection Class IP21S | |||
Plasma Arc Starting Piolt L/F | |||
Air Flow Pressure (MPA) 0.5 (75 psi) | |||
Air Flow Rate (CFM) 6.70 | |||
Cutting Thickness - Clean (Inch) 5/8 | |||
Cutting Thickness - Severance (Inch) 25/32 | |||
Dimensions (inch) 18.1" x 6.69" x 12.99" | |||
Weight (Pounds) 20.2 | |||
'''Kerf:''' The tip orifices focus the plasma stream to the work piece. It is important to use the correct size tip for the amperage being used, for example a tip with a 3/64" orifice is good for 0-40 amps whereas a 1/16" orifice is better for 40-80 amps | |||
'''Air Pressure and Volume:''' The RazorCut45 air pressure is pre-set at 4.5 psi and requires a flow rate of 6.0 CF/M. | |||
Latest revision as of 12:06, 15 March 2022
|
Shop Area: Metal Shop Tool: Plasma Cutter (handheld) Requires in-person training: Yes Procedure Number: MT 110-03, Rev. 1 Last Revision: 4/30/2021 |
GENERAL
The RazorCut 45 plasma cutter is used for making curved cuts in metal. It can cut up to 5/8" thick steel and 1/4" aluminum.
REFERENCE
- Razor Cut 45 product page (http://razorweld.com/catalogue_product.asp?product=983&category=22&subcategory=87)
- Razor Cut 45 operating manual
- Cutmaster 82 Operating Manual
- Cutmaster 82 Service Manual
MAINTENANCE
LIST OF SPECIFICATIONS
The RazorCut 45 is retrofit with a genuine IPT 60 torch.
Recommended tip orifice sizes:
20 amp tip - 0.6mm/.025" - 15 to 20 amps - 50 to 55 psi
30 amp tip - 0.8mm/.030" - 21 to 30 amps - 55 to 60 psi
40 amp tip - 0.9mm/.035" - 31 to 40 amps - 65 to 70 psi
50 amp tip - 1.0mm/.040" - 41 to 50 amps - 65 to 75 psi
60 amp tip - 1.1mm/.044" - 51 to 60 amps - 65 to 75 psi
70 amp tip - 1.2mm/.047" - 61 to 70 amps - 75 to 80 psi
80 amp tip - 1.3mm/.051" - 71 to 80 amps - 75 to 80 psi
These are a few of the important details in regards to the Razorcut 45 Plasma Cutter.
Technical Data
Power Supply / Phases (V-Ph) 230v - 1 +/- 15%
Duty Cycle @ 104°F 30% @ 45Amps
Rated Power (KVA) 5.50
Output Current Range (A) Plasma 20-40
Rated Output Voltage (V) 96
Efficiency (%) 90
Insulation Class H
Protection Class IP21S
Plasma Arc Starting Piolt L/F
Air Flow Pressure (MPA) 0.5 (75 psi)
Air Flow Rate (CFM) 6.70
Cutting Thickness - Clean (Inch) 5/8
Cutting Thickness - Severance (Inch) 25/32
Dimensions (inch) 18.1" x 6.69" x 12.99"
Weight (Pounds) 20.2
Kerf: The tip orifices focus the plasma stream to the work piece. It is important to use the correct size tip for the amperage being used, for example a tip with a 3/64" orifice is good for 0-40 amps whereas a 1/16" orifice is better for 40-80 amps
Air Pressure and Volume: The RazorCut45 air pressure is pre-set at 4.5 psi and requires a flow rate of 6.0 CF/M.