Cnc plasma maintenance and specifications: Difference between revisions
No edit summary |
Aspontarelli (talk | contribs) |
||
Line 17: | Line 17: | ||
= General = | = General = | ||
We run a Lotos LTP5500 plasma cutter on the Langmuir Crossfire CNC plasma table. | |||
[http://www.langmuirsystems.com/crossfire Langmuir Crossfire CNC Plasma Table]. | [http://www.langmuirsystems.com/crossfire Langmuir Crossfire CNC Plasma Table]. | ||
[[File:CNC Plasma Cutter.png]] | [[File:CNC Plasma Cutter.png]] |
Revision as of 12:58, 4 October 2021
Shop Area: Metal Shop Tool: CNC Plasma Cutter Requires in-person training: Yes |
Procedure Number MT 130-05, Rev. 1 |
Date 2/8/2021 |
General
We run a Lotos LTP5500 plasma cutter on the Langmuir Crossfire CNC plasma table.
Langmuir Crossfire CNC Plasma Table.
Reference
- https://www.langmuirsystems.com/troubleshooting
- https://www.langmuirsystems.com/crossfire/legacy
- https://unimig.com.au/wp-content/uploads/2019/08/RAZOR-CUT-45-Manual.pdf
Maintenance
Razorcut 45 Plasma Cutter
Exposure to extremely dusty, damp, or corrosive air is damaging to the welding/cutting machine. In order to prevent any possible failure or fault of this welding/ cutting equipment, clean the dust at regular intervals with clean and dry compressed air of required pressure.
Specifications
These are a few of the important details in regards to the Razorcut 45 Plasma Cutter.
Technical Data
Power Supply / Phases (V-Ph) 230v - 1 +/- 15%
Duty Cycle @ 104°F 30% @ 45Amps
Rated Power (KVA) 5.50
Output Current Range (A) Plasma 20-40
Rated Output Voltage (V) 96
Efficiency (%) 90
Insulation Class H
Protection Class IP21S
Plasma Arc Starting Piolt L/F
Air Flow Pressure (MPA) 0.5 (75 psi)
Air Flow Rate (CFM) 6.70
Cutting Thickness - Clean (Inch) 5/8
Cutting Thickness - Severance (Inch) 25/32
Dimensions (inch) 18.1" x 6.69" x 12.99"
Weight (Pounds) 20.2
Torch Type: TRF-45-6-CC1 Plasma torch
Kerf: The tip orifices focus the plasma stream to the work piece. It is important to use the correct size tip for the amperage being used, for example a tip with a 3/64" orifice is good for 0-40 amps whereas a 1/16" orifice is better for 40-80 amps
Air Pressure and Volume: The RazorCut45 air pressure is pre-set at 4.5 psi and requires a flow rate of 6.0 CF/M.
CROSSFIRE™ SPECIFICATIONS
- Cutting Envelope Dimensions:25.3” (X) x 23.3” (Y) x 3.0" (Z)
- Machine Weight:130 Pounds
- Linear Bearing Type: Ball Bearing Carriages on Zinc-plated Steel Tube Rails
- Stepper Motor Size: X-Axis 284 oz-in Y-Axis 425 oz-in
- PC Interface: Windows USB
- Mechanical Drive System:3/8”-8 4-Start ACME Lead Screws and Acetal Anti-Backlash Lead Nuts
- Motion Accuracy:0.002” per 12” inches
- Step Resolution:0.0005”
- Maximum Cut Speed:300 ipm
- Torch Height Control: Manual Torch Height Adjustment
- Table Surface: Replaceable Steel Slats, 50mm wide x 3mm thick
- Input Power: 110/220 VAC (selectable)
END OF THE PROCEDURE