Table saw maintenance and specifications

Shop Area: Woodshop Tool: Table Saw

Procedure Number MT 110-03, Rev. 0

Date DRAFT

General

Powermatic Model PM2000 Table Saw Jet Model 708675PK Table Saw

Reference

• Link to Instructions and Parts Manual  http://content.powermatic.com/manuals/1792000K_man.pdf
• Link to Jet https://www.woodcraft.com/media/W1siZiIsIjIwMjAvMDMvMTQvMDAvNTEvMTcvNTkvODM3NDc0LkpldC5YQUNUQWgucGRmIl1d/837474.Jet.XACTAh.pdf?sha=1db8234d267f663e
• https://www.woodcraft.com/products/jet-xactasaw-deluxe-table-saw-3hp-1ph-50-rip?gclid=Cj0KCQiA2uH-BRCCARIsAEeef3mySTa69vTv_Vhu-fzCgKBm6Sx_6_2HxkXGwHv55VeE5P5t_QiOcEgaAmYHEALw_wcB#
•  

Maintenance

Cleaning

Note: The following maintenance schedule assumes the saw is being used every day.

Daily:

• Wipe down the table surface and grooves with a rust preventive.

• Clean the pitch and resin from the saw blade.

Weekly:

• Table surface must be kept clean and free of rust for best results. Apply a coat of paste wax to the surface to facilitate this. An alternative is to apply white talcum powder, rubbed in vigorously once a week with a blackboard eraser; this will fill casting pores and form a moisture barrier. This method provides a table top that is slick and allows rust rings to be easily wiped from the surface. Important also is the fact that talcum powder will not stain wood or mar finishes as wax pickup does.

• Clean the motor housing with compressed air.

• Wipe down the fence rails with a dry silicon lubricant.

Periodic:

• Keep the inside of the cabinet and trunnion area clean.

• Check for excessive play in the tilting and raising mechanism and in the saw arbor and re-adjust as required.

• Check for belt tension and wear. Readjust or replace belt as required.

Lubrication

• Grease the tilting worm gear, raising worm gear, castor system worm gear and the trunnion areas with a good grade non-hardening grease.

• Check all adjustments after lubricating.

Miscellaneous Always be aware of the condition of your machine. Routinely check the condition of the following items and repair or replace as necessary:

• Mounting bolts

• Power switch

• Saw blade

• Blade guard assembly

JET Blade Installation/Replacement

To install or replace a blade (refer to Figure 6), 27mm Wrench is needed.

1. Disconnect machine from power source.

2. Raise the blade height all the way up and set the blade tilt to 0º.

3. Remove the table insert.

4. Rotate the arbor to line up the slot (C) with the arbor lock (D).

5. Press the arbor lock (D) in the direction shown by the arrow to engage it into the slot (C) in the arbor. At the same time remove the arbor nut (A), loosening with a 27mm wrench if necessary.

6. Remove the collar (B).

7. Install the blade, making sure the cutting teeth at the top of the blade point toward the front of the saw.

8. Replace the collar (B) and arbor nut (A).

9. Engage the arbor lock (D) and tighten the nut (A) with a 27mm wrench.

10. Lower the blade below the table.

List of Specifications

Model number ......................................................................................................................... PM2000

Stock Number

 3HP, 230V, 60Hz, 1 Phase, 3600 RPM, TEFC ......................................................................1791999

 5HP, 230V, 60Hz, 1 Phase, 3600 RPM, TEFC ......................................................................1791998

 5HP, Prewired 230V (for 460V see Note below), 60Hz, 3 Phase, 3600 RPM, TEFC ................1791997

Table size with standard extensions (L x W/in.)...................................................................... 42 x 30 1/2

Table size without extensions (L x W/in.) ............................................................................... 22 x 30 1/2

Arbor diameter (in.) .......................................................................................................................... 5/8

Saw blade diameter (in.) ................................................................................................................... 10

Arbor speed (RPM) ....................................................................................................................... 4300

Left tilt range ................................................................................................................................ 0–45

Maximum depth of cut (in.) ........................................................3-1/8 at 90-degrees; 2-1/8 at 45-degrees

Maximum diameter of dado (in.)........................................................................................................... 8

Maximum width of dado cut (in.) ................................................................................................... 13/16

Drive system ....................................................................................................................... Poly-V Belt

Table height to floor (in.) ............................................................................................................. 34-1/2

Dust port diameter (in.) ....................................................................................................................... 4

Shipping weight (saw only) ......................................................... All Models: Net: 540 lbs, Gross: 604 lbs

JET

Stock Numbers ............................................................................................................... 708674 (3 HP, 1 Ph)

............................................................................................................................. 708676 (5 HP, 1 Ph)

............................................................................................................................. 708680 (5 HP, 3 Ph)

Blade Diameter .......................................................................................................................................... 10”

Arbor Diameter .......................................................................................................................................... 5/8”

Maximum Depth of Cut ................................................................................................................................ 3”

Maximum Thickness at 45 Cut ............................................................................................................. 2-1/8”

Table in Front of Saw Blade at Maximum Cut ........................................................................................... 10”

Maximum Width of Dado ....................................................................................................................... 13/16”

Maximum Diameter of Dado ........................................................................................................................ 8”

Dust Port Diameter ....................................................................................................................................... 4”

Dust Collection Minimum CFM required ................................................................................................... 350

Table Height ............................................................................................................................................... 34”

Table Size (with extension) ......................................................................................................... 29"D x 42"W

Table Size (without extension) .................................................................................................... 29"D x 20”W

Arbor Speed ................................................................................................................................... 4300 RPM

Sound Rating:

(without blade) ...................................................................................................................... 70 dB at 3 ft.

(with 10”x50T blade) ............................................................................................................ 85 dB at 3 ft.

Motor

SN 708674 .......................................................................................................... 3HP, 1Ph, 230V only

SN 708676 ......................................................................................................... 5 HP, 1Ph, 230V only

SN 708680 .................................................... 5HP, 3Ph, 230/460V, prewired 230V 

Weight

Net ............................................................................................................................................ 330 lbs.

Gross ........................................................................................................................................ 407 lbs.

 

THIS IS THE END OF THE PROCEDURE