Pipe and tube bender maintenance and specifications - Revision history

Kbogacik: /* Specifications */

2021-02-21T19:32:15Z

Specifications

← Older revision		Revision as of 15:32, 21 February 2021
Line 37:		Line 37:
	= Specifications =		= Specifications =

	[[File:Tube Bender.png]]		[[File:Tube Bender Specs.png]]

	'''END OF THE PROCEDURE'''		'''END OF THE PROCEDURE'''

Kbogacik: /* Maintenance */

2021-02-21T19:30:08Z

Maintenance

← Older revision		Revision as of 15:30, 21 February 2021
Line 33:		Line 33:
	* To prevent corrosion in environments where the machine is used periodically, the top of the mounting plate, sliding surfaces of the handle and nose holder assemblies, and other nonlubricated bare metal surfaces may be protected with a suitable film coating such as paste wax, beeswax, Boeshield T-9, or similar.		* To prevent corrosion in environments where the machine is used periodically, the top of the mounting plate, sliding surfaces of the handle and nose holder assemblies, and other nonlubricated bare metal surfaces may be protected with a suitable film coating such as paste wax, beeswax, Boeshield T-9, or similar.

	[[File:Tube Bender.png]]		[[File:Tube Bender Lub.png]]

	= Specifications =		= Specifications =

Kbogacik at 19:29, 21 February 2021

2021-02-21T19:29:05Z

← Older revision		Revision as of 15:29, 21 February 2021
Line 9:		Line 9:
	'''Procedure Number'''		'''Procedure Number'''

	MT 130-10, Rev. 0		MT 130-10, Rev. 1
	\|width="33%"\|		\|width="33%"\|
	'''Date'''		'''Date'''

	~~DRAFT~~		2/21/2021
	\|}		\|}

	= General =		= General =

	Di-~~acro~~ Metal Fabrication Bender No. 2.		'''Di-Acro Metal Fabrication Bender No. 2'''

			[[File:Tube Bender.png]]

	= Reference =		= Reference =
Line 30:		Line 32:
	* Lubricate bearings per the table below via the Drive Fitting in the side of the Handle Arm Weldment with a NLGI GC-LB or SAE J310 grease per the lubrication guide, below.		* Lubricate bearings per the table below via the Drive Fitting in the side of the Handle Arm Weldment with a NLGI GC-LB or SAE J310 grease per the lubrication guide, below.
	* To prevent corrosion in environments where the machine is used periodically, the top of the mounting plate, sliding surfaces of the handle and nose holder assemblies, and other nonlubricated bare metal surfaces may be protected with a suitable film coating such as paste wax, beeswax, Boeshield T-9, or similar.		* To prevent corrosion in environments where the machine is used periodically, the top of the mounting plate, sliding surfaces of the handle and nose holder assemblies, and other nonlubricated bare metal surfaces may be protected with a suitable film coating such as paste wax, beeswax, Boeshield T-9, or similar.

			[[File:Tube Bender.png]]

	= Specifications =		= Specifications =

	'''~~THIS IS THE~~ END OF THE PROCEDURE'''		[[File:Tube Bender.png]]

			'''END OF THE PROCEDURE'''

Aspontarelli: Created page with "{| |width="33%"| '''Shop Area:''' Metal Shop '''Tool:''' Pipe and Tube Bender '''Requires in-person training:''' Yes |width="33%"| '''Procedure Number''' MT 130-10, Rev...."

2020-12-31T11:33:47Z

Created page with "{| |width="33%"| '''Shop Area:''' Metal Shop '''Tool:''' Pipe and Tube Bender '''Requires in-person training:''' Yes |width="33%"| '''Procedure Number''' MT 130-10, Rev...."

New page

{|
|width="33%"|
'''Shop Area:''' Metal Shop

'''Tool:''' Pipe and Tube Bender

'''Requires in-person training:''' Yes
|width="33%"|
'''Procedure Number'''

MT 130-10, Rev. 0
|width="33%"|
'''Date'''

DRAFT
|}

= General =

Di-acro Metal Fabrication Bender No. 2.

= Reference =

* [https://www.diacro.com/wp-content/uploads/2016/07/Art-Of-Bending_2013.pdf '''ART OF BENDING''']

= Maintenance =

* Keep machine surfaces clean and free of debris.
* Periodically add grease in grease fitting.
* Lubricate bearings per the table below via the Drive Fitting in the side of the Handle Arm Weldment with a NLGI GC-LB or SAE J310 grease per the lubrication guide, below.
* To prevent corrosion in environments where the machine is used periodically, the top of the mounting plate, sliding surfaces of the handle and nose holder assemblies, and other nonlubricated bare metal surfaces may be protected with a suitable film coating such as paste wax, beeswax, Boeshield T-9, or similar.

= Specifications =

'''THIS IS THE END OF THE PROCEDURE'''