Drill-press-user-guide - Revision history

Elise: /* GENERAL */

2024-05-30T20:25:39Z

GENERAL

← Older revision		Revision as of 16:25, 30 May 2024
Line 21:		Line 21:

	The drill press cuts holes of different sizes in different materials. It can be used to drill wood, plastics, ceramics, or metals. What matters when drilling the different materials is the type of drill bit chosen.		The drill press cuts holes of different sizes in different materials. It can be used to drill wood, plastics, ceramics, or metals. What matters when drilling the different materials is the type of drill bit chosen.
			[[File:Woodworking Drill Press.jpg\|left\|thumb]]
	[[File:~~Screenshot 2021-01-18 134226~~.~~png~~]]

	= SAFETY =		= SAFETY =

Aspontarelli: /* TROUBLESHOOTING */

2022-04-19T10:16:47Z

TROUBLESHOOTING

← Older revision		Revision as of 06:16, 19 April 2022
Line 58:		Line 58:


	== ~~'''~~Bits Wandering~~'''~~ ==		== Bits Wandering ==


Line 71:		Line 71:
	* Also make sure that the chuck jaws are firm and properly tightened to keep the bits in its place.		* Also make sure that the chuck jaws are firm and properly tightened to keep the bits in its place.

	== ~~'''~~Noisy Operations~~'''~~ ==		== Noisy Operations ==

	Causes		Causes
Line 82:		Line 82:
	* Constantly grease the spindle to avoid it from going dry on a timely basis depending on how often and how long the drill press is used.		* Constantly grease the spindle to avoid it from going dry on a timely basis depending on how often and how long the drill press is used.

	== ~~'''~~Wood Splinters Underside (chip-out)~~'''~~ ==		== Wood Splinters Underside (chip-out) ==

	Causes		Causes
Line 92:		Line 92:
	* [https://www.sciencedaily.com/releases/2014/05/140507095851.htm Make use of scrap woods] or pieces under the current workpiece to give it all the support it needs.		* [https://www.sciencedaily.com/releases/2014/05/140507095851.htm Make use of scrap woods] or pieces under the current workpiece to give it all the support it needs.

	== ~~'''~~Wobbling Drill Bits~~'''~~ ==		== Wobbling Drill Bits ==

	Causes		Causes
Line 108:		Line 108:


	== ~~'''~~Binding or Slipping Work Piece~~'''~~ ==		== Binding or Slipping Work Piece ==

	Causes		Causes
Line 118:		Line 118:
	* To solve this, all you need to do is to install the bits properly and ensure they are well secured in its place.		* To solve this, all you need to do is to install the bits properly and ensure they are well secured in its place.

	== ~~'''~~Loosening Work Piece~~'''~~ ==		== Loosening Work Piece ==

	Causes		Causes

Aspontarelli: /* PROCEDURE */

2022-04-19T10:16:11Z

PROCEDURE

← Older revision		Revision as of 06:16, 19 April 2022
Line 49:		Line 49:
	** Harder materials - lower speeds		** Harder materials - lower speeds
	* Place scrap wood beneath your part to avoid drilling into the table		* Place scrap wood beneath your part to avoid drilling into the table
			* Use clamping when drilling small parts
	* For deep holes, may need to peck drill to remove chips from hole		* For deep holes, may need to peck drill to remove chips from hole
	* Put bits away– don't leave them in the chuck (easy to forget)		* Put bits away– don't leave them in the chuck (easy to forget)
	* Use clamping when drilling small parts
	* Sweep up		* Sweep up

Aspontarelli: /* PROCEDURE */

2022-04-19T10:15:53Z

PROCEDURE

← Older revision		Revision as of 06:15, 19 April 2022
Line 50:		Line 50:
	* Place scrap wood beneath your part to avoid drilling into the table		* Place scrap wood beneath your part to avoid drilling into the table
	* For deep holes, may need to peck drill to remove chips from hole		* For deep holes, may need to peck drill to remove chips from hole
	* Don't lose the chuck key
	* Put bits away– don't leave them in the chuck (easy to forget)		* Put bits away– don't leave them in the chuck (easy to forget)
	* Use clamping when drilling small parts		* Use clamping when drilling small parts
			* Sweep up
	~~'''DIAL SPEEDS - RANGES, 1 50-2000 RPM - with VARIABLE SPEED COUNTERSHAFT DRIVE'''~~
	* ~~Turn the dial while drill is running to select the best RPM for the job.~~
	* Heavy-duty drive is built to deliver full power to the spindle at all speeds:
	** three V-belts and cog belt transmit positive-power to spindle
	** variable speed and spindle drive pulleys are cast iron, fully machined and balanced
	** there are eight lubricated-for-life bearings for smooth performance.


	= TROUBLESHOOTING =		= TROUBLESHOOTING =

Aspontarelli: /* REFERENCE */

2022-04-18T10:56:06Z

REFERENCE

← Older revision		Revision as of 06:56, 18 April 2022
Line 38:		Line 38:

	* Basic use and safety video (https://www.youtube.com/watch?v=Nu9tYcld7ck)		* Basic use and safety video (https://www.youtube.com/watch?v=Nu9tYcld7ck)
			* Workholding tips video (https://www.youtube.com/watch?v=yrN5dl1p3K0)

	= PROCEDURE =		= PROCEDURE =

Aspontarelli: /* TROUBLESHOOTING */

2022-04-12T10:53:39Z

TROUBLESHOOTING

← Older revision		Revision as of 06:53, 12 April 2022
Line 64:		Line 64:



	~~== '''Excessive Vibration''' ==~~

	~~Causes~~

	* When the spindle or table handles go faulty, the drill press is likely to have excessive vibration.
	* High power voltage can also be responsible for excessive vibration of the drill press.

	~~Solutions~~

	* Make sure the drill press works at a power rate that is very stable at all times. A power stabilizer can be best to secure this.
	* Make sure the spindle handles are well and in place all the time, in use and out of use.

	== '''Bits Wandering''' ==		== '''Bits Wandering''' ==

Kbogacik at 21:02, 25 January 2021

2021-01-25T21:02:25Z

← Older revision		Revision as of 17:02, 25 January 2021
Line 9:		Line 9:
	'''Procedure Number'''		'''Procedure Number'''

	UG 110-06, Rev. 1		UG 110-06, Rev. 2
	\|width="33%"\|		\|width="33%"\|
	'''Date'''		'''Date'''

	1/18/2021		1/25/2021
	\|}		\|}

Kbogacik at 20:33, 25 January 2021

2021-01-25T20:33:56Z

← Older revision		Revision as of 16:33, 25 January 2021
Line 52:		Line 52:
	* Put bits away– don't leave them in the chuck (easy to forget)		* Put bits away– don't leave them in the chuck (easy to forget)
	* Use clamping when drilling small parts		* Use clamping when drilling small parts

			'''DIAL SPEEDS - RANGES, 1 50-2000 RPM - with VARIABLE SPEED COUNTERSHAFT DRIVE'''
			* Turn the dial while drill is running to select the best RPM for the job.
			* Heavy-duty drive is built to deliver full power to the spindle at all speeds:
			** three V-belts and cog belt transmit positive-power to spindle
			** variable speed and spindle drive pulleys are cast iron, fully machined and balanced
			** there are eight lubricated-for-life bearings for smooth performance.


	= TROUBLESHOOTING =		= TROUBLESHOOTING =
Line 144:		Line 152:


	'''END OF THE PROCEDURE'''		'''END OF THE PROCEDURE'''

Kbogacik: /* Loosening Work Piece */

2021-01-25T20:20:46Z

Loosening Work Piece

← Older revision		Revision as of 16:20, 25 January 2021
Line 144:		Line 144:


	'''~~THIS IS THE~~ END OF THE PROCEDURE'''		'''END OF THE PROCEDURE'''

Kbogacik at 18:59, 18 January 2021

2021-01-18T18:59:44Z

← Older revision		Revision as of 14:59, 18 January 2021
Line 9:		Line 9:
	'''Procedure Number'''		'''Procedure Number'''

	UG 110-06, Rev. 0		UG 110-06, Rev. 1
	\|width="33%"\|		\|width="33%"\|
	'''Date'''		'''Date'''

	~~DRAFT~~		1/18/2021
	\|}		\|}