vector-space.org - User contributions [en]

Brother-pr655-embroidery-machine

2026-07-17T19:42:57Z

Mwalsh: jh

{|
|width="33%"|
'''Shop Area:''' Textiles

'''Tool:''' Brother PR655 Embroidery Machine

'''Requires in-person training:''' Peer-to Peer Training Recommened
|width="33%"|
'''Procedure Number'''

UG 141-01, Rev. 1
|width="33%"|
'''Date'''

07/01/2026
|}
[[File:Embroidery.jpg|thumb|Embroidery with the Brother PR655]]
= GENERAL =
{| class="wikitable"
|+
!Feature
!Brother PR655
|-
|Embroidery Area
|12" x 8"
|-
|Needle Count
|6
|-
|Max Speed
|1,000 SPM
|-
|Built-in Designs
|25 + 60 (USB)
|-
|Display Technology
|HD LCD Touchscreen
|}

Brother PR655 Embroidery Machine '''Manual''' : https://download.brother.com/welcome/doch001115/pr655ug01en.pdf

= SAFETY =

This is generally considered a safe machine, however any machine that is used improperly could be hazardous. While sewing always keep hands clear of the embroidery area.

= PROCEDURE =
Power on the machine, power button is located on the back right. Touch screen to begin. There are several designs to choose from Check the machine to see what kind of attachments are in place and to make sure all of the needles are threaded. Chose a fabric and stabilizer and attach to a 'Fast Frame' (this is the most convenient and commonly used style of attaching your work piece to the machine) stabilizers are set underneath your fabric of choice (unless you embroidering on a knit fabric those require a special top stabilizer). Setup the design in the machine and embroider.

== My First Embroidery ==
''Embroider your initials''
[[File:Letters .jpg|left|thumb|256x256px|Step 1.4 ]]
This is a predetermined project laid out step-by-step to guide you in practicing base knowledge for this tool.
[[File:Fast frame .jpg|left|thumb|259x259px|Fast Frames Step 2.1 ]]
[[File:My First Project .jpg|left|thumb|263x263px|My First Project ]]
# '''Setting up the design'''
## Turn on the Machine (a little song to welcome you chimes)
##Touch screen to begin
##"The machine will move" message pops (its not lying) move your hands and press "OK"
##Choose one color font (see photo "step 1.4" )
##Choose your letters
##When you are ready to progress to the next step press "SET"
##Notice the size of your piece (you may adjust size or rotation in this screen)
##when your finished editing press "END EDIT"
#'''It's time to set up the work area.'''
##Keeping in mind your project size choose a "fast track" or "fast frame" (they are the same thing, names used interchangeably name) These are the most typical attachment used, and is the most likely to be set up at the machine when you arrive. They are stored over the work bench. (Image 2.1)
##Choose your fabric, a piece of cotton or lightweight canvas should do nicely.
##Find the "stabilizer" this is used on every embroidery project to, well... stabilize the piece while embroidering. It's white and semi opaque. Typically lives under the embroidery work bench or in embroidery storage to the right of the machine.
##Cut both the fabric and stabilizer to fit the chosen fast frame, the stabilizer goes on the top of the fast frame then the fabric on top of that. Attach using binder clips.
##Great! Now its time to attach the fast frame to the Fast Frame "Arm" (if the fast frame receiver is not already there follow the steps in this video: https://youtu.be/S3WEFdFloas?si=fVz_3zm2kZFeg5Cv > second 56) If the frame is attached this should be as simple as loosening the middle knob, putting on the fast frame and settling it into place, and tightening the knob to secure the frame.
##Check the thread color in the first position this will be your color for your first project.
# '''Embroider'''
##Now you're ready to trace out your initials to make sure they fit on your workspace. Use the trace button (white square with a dotted line around it) if the needles hit metal the are likely to break. Change size of your embroidery in previous screens if needed.
##You are ready to embroider. Push the "SEWING" button to advance to the next screen
##Push the lock button on the screen and the arrow below will flash green push that too the machine will begin sewing now!
##Watch your project happen! If you have any trouble along the way check out the troubleshooting section. When it's finished detach everything and trim or tear away your stabilizer.
##Tidy up and done!

== My Second Embroidery ==
''Multicolor preloaded design''
[[File:Thread icon position number .jpg|thumb|Position number image 1.8 ]]
Many steps from the first project will repeat here. New steps are italicized.
#'''Setting up the design'''
## Turn on the Machine (a little song to welcome you chimes)
##Touch screen to begin
##"The machine will move" message pops (its not lying) move your hands and press "OK"
##''Choose a multicolor design'' ''and press "SET"''
##Notice the size of your piece in the middle grey bar (you may adjust size or rotation in this screen)
##When your finished editing press "END EDIT"
##Press "SEWING"
##''When you are in the sewing screen notice the thread icons, the numbers next to them represent thier position on the machine (positions 1-6). (image 1.8) The colors that show up on the screen represent the colors seen in the design. This is obvious but, the colors on the physical thread rack on the back of the machine are the colors that will actually be embroidered in thier corresponding position. We won't go into changing the color of the tread spool icon, only the changing of the physical thread.''
#'''''Changing threads.'''''
##''Cut the string for the previous position one thread just above the spool.''
##''Remove the previous thread and put your chosen thread in its place. Embroidery threads are stored next to the machine on the metal rack.''
##''Without pulling the previous thread too much tie the two tails together. You will be using the previous thread as a guide to pull the new thread through the machine, this is much faster than than threading the machine by hand and works very well, however it is very good to learn the threading process so that you can know when there is a threading issue when troubleshooting. How to thread : https://www.youtube.com/watch?v=Vk_xvHxAVv4''
##''Remove the lowest part of the thread from the needle only. Pull the thread from the bottom and watch it pull all the way through the machine.''
##''Thread the needle leaving a bit of a tail.''
##''Repeat those steps for each thread position.''
#'''It's time to set up the work area.'''
##Keeping in mind your project size choose a "fast track" or "fast frame" (they are the same thing, names used interchangeably name) These are the most typical attachment used, and is the most likely to be set up at the machine when you arrive. They are stored over the work bench. (Image 2.1)
##Choose your fabric, a piece of cotton or lightweight canvas should do nicely.
##Find the "stabilizer" this is used on every embroidery project to, well... stabilize the piece while embroidering. It's white and semi opaque. Typically lives under the embroidery work bench or in embroidery storage to the right of the machine.
##Cut both the fabric and stabilizer to fit the chosen fast frame, the stabilizer goes on the top of the fast frame then the fabric on top of that. Attach using binder clips.
##Great! Now its time to attach the fast frame to the Fast Frame "Arm" (if the fast frame receiver is not already there follow the steps in this video: https://youtu.be/S3WEFdFloas?si=fVz_3zm2kZFeg5Cv > second 56) If the frame is attached this should be as simple as loosening the middle knob, putting on the fast frame and settling it into place, and tightening the knob to secure the frame.
##Check the thread color in the first position this will be your color for your first project.
# '''Embroider'''
##Now you're ready to trace out your initials to make sure they fit on your workspace. Use the trace button (white square with a dotted line around it) if the needles hit metal the are likely to break. Change size of your embroidery in previous screens if needed.
##You are ready to embroider. Push the "SEWING" button to advance to the next screen
##Push the lock button on the screen and the arrow below will flash green push that too the machine will begin sewing now!
##Watch your project happen! If you have any trouble along the way check out the troubleshooting section. When it's finished detach everything and trim or tear away your stabilizer.
##Tidy up and done!

== My Third Embroidery ==
''Custom embroidery digitizing with Inkstitch'' https://www.youtube.com/watch?v=mPaGwjwpzWc

== My Forth Embroidery ==
''Embroidering a hat'' https://www.youtube.com/watch?v=koOPpVUuSC4

= TROUBLESHOOTING =

* Always check that the machine is '''threaded properly''', sewing machines of any kind are notoriously particular when it comes to threading, the tiniest missed detail can lead to problems obvious in the quality of your product. https://www.youtube.com/watch?v=Vk_xvHxAVv4
* Make sure '''tread tail''' is long enough to not pull out of the needle as soon sewing begins
* Make sure the '''bobbin spool''' is seated correctly. There is a magnet in these fancy pre-wound bobbins we buy, the magnet should always face in towards the metal bobbin case. If the spool is not turning in the correct direction or if its not seated well the machine will be embroidering will be interrupted regularly with error messages and your piece will be low quality.
* Check that the '''bobbin spool''' is more than a quarter full, when the bobbin thread gets low it tends to make the machine perform poorly.
* '''Needles''', they can break and dull regularly with use. Check to make sure needles aren't broken. If the needles are dull they can easily cause issues. It's normal to troubleshoot replacing needles if you've already made sure the machine is threaded properly. If you are a normal user of this machine or any sewing machine learning to change the needles is part of what you'll need to know for success. Video tutorial on needle changing: https://www.youtube.com/watch?v=89EveDvM6k0
* The '''tension''' is not this issue as frequently as one might think. Ancel, our area Shop Captain has spent a lot of time understanding and tinkering with tension on this machine to get it into tip-top shape. Adjusting tension dramatically will likely ''not'' yield the desired results. If you are adjusting tension for trouble shooting please do so thoughtfully always being able to return the tension to its original position if that was not in fact the issue.

= <big>REFERENCE</big> =
* Hat attachment video (https://www.youtube.com/watch?v=koOPpVUuSC4)
* Custom embroidery digitizing with Inkstitch (https://www.youtube.com/watch?v=mPaGwjwpzWc)
* Threading, bobbin, and color change Tutorial (https://www.youtube.com/watch?v=Hmb22uwrJZ4)
* Ode to the PR655 and general use (https://www.maggieframes.com/blogs/embroidery-blogs/brother-pr655-ultimate-guide-mastering-your-6-needle-embroidery-machine)
* Glossary of terms (https://kimberbell.com/blogs/thekimberbellablog/machine-embroidery-glossary-of-terms?srsltid=AfmBOopqK-5z8W5BCG8x9qDt5MqvqbmO1LrQKS6Tr2qFypRPuW49Uj0E)
'''END OF THE PROCEDURE'''

Membership Resources

2026-07-17T19:36:21Z

Mwalsh:

Membership to Vector Space is an exciting endeavor that requires personal responsibility and commitment to policies that keep our makerspace ecosystem running smoothly. Your membership is capable of providing you with not only several adequate work spaces but also with the opportunity to join into a community of vibrant creators. The purpose of this article is to collect into one place all the resources that help your membership thrive.

== Member Handbook ==
[[File:Member Handbook .jpg|thumb]]
Each member receives there own hard copy of the member handbook at orientation. The handbook covers a variety of topics including our mission statement , policies, organization of the leadership team, org chart, annual events, a glossary of terms and more.

https://vector-space.org/member-handbook

== Advanced Scavenger Hunt ==
Members can test their makerspace knowledge for a chance to win a Vector Space enamel pin! https://vector-space.org/advanced-member-scavenger-hunt

== How to use Slack ==
''What is Slack?'' Slack is the digital platform where community stays active between visits to the physical space. It's where people share projects, ask for help, report a down tool, hear about workshop openings, and find out what's happening around the makerspace. Think of it as the community bulletin board that's always up to date. The information is organized nicely into channels (kind of like bulletin boards for different shop areas and projects) so you can choose to stay updated on what's relevant to you.

There are great videos out there that quickly take you through a few features and can help get you up and running easily. We've selected a few for you here.

'''Slack troubleshooting'''
{| class="wikitable"
|+
!Problem
!Answer
!fix
|-
|Can't find any channels or people in Slack
|You are most likely signed into the wrong workspace or accidentally created one called "Vector Space" instead of signing into our slack workplace that already exists.
|In the slack app, click on the logo icon in the top left corner and choose the proper workspace. The proper workspace shows the Vector Space logo
|-
|
|
|
|-
|
|
|
|}
'''Slack tutorials'''

~ How to join a channel https://www.youtube.com/watch?v=ZErbE6euptE

~ How to add a profile picture https://www.youtube.com/watch?v=Yu_9XU9ogJ4

~ How to leave an emoji reaction on a post https://www.youtube.com/watch?v=oZdcqMc2tnw

~ How to reply within a conversation thread https://www.youtube.com/watch?v=E5TAbDD05Mk

Membership Resources

2026-07-15T16:51:42Z

Mwalsh: added slack section

Membership to Vector Space is an exciting endeavor that requires personal responsibility and commitment to policies that keep our makerspace ecosystem running smoothly. Your membership is capable of providing you with not only several adequate work spaces but also with the opportunity to join into a community of vibrant creators. The purpose of this article is to collect into one place all the resources that help your membership thrive.

== Member Handbook ==
[[File:Member Handbook .jpg|thumb]]
Each member receives there own hard copy of the member handbook at orientation. The handbook covers a variety of topics including our mission statement , policies, organization of the leadership team, org chart, annual events, a glossary of terms and more.

https://vector-space.org/member-handbook

== Advanced Scavenger Hunt ==
Members can test their makerspace knowledge for a chance to win a Vector Space enamel pin! https://vector-space.org/advanced-member-scavenger-hunt

== How to use Slack ==
''What is Slack?'' Slack is where the community lives between visits to the physical space. It's where people share projects, ask for help, hear about workshop openings, and find out what's happening around the makerspace. Think of it as the community bulletin board that's always up to date. The information is organized nicely into channels (kind of like bulletin boards for different shop areas and projects) so you can choose to stay updated on what's relevant to you.

There are great videos out there that quickly take you through a few features and can help get you up and running easily. We've selected a few for you here.

'''Slack troubleshooting'''
{| class="wikitable"
|+
!Problem
!Answer
!fix
|-
|Can't find any channels or people in Slack
|Signed into the wrong workspace or accidentally created one called "Vector Space" instead of signing into our slack workplace that already exists.
|in the slack phone app- click on the logo icon in the top left corner and choose the proper workspace. The proper workspace shows the Vector Space logo
on the Desktop- similarly the icon to change workspaces is shown in the top left corner of the slack window.
|-
|
|
|
|-
|
|
|
|}

Brother-pr655-embroidery-machine

2026-07-09T15:17:58Z

Mwalsh: ufsyuk

{|
|width="33%"|
'''Shop Area:''' Textiles

'''Tool:''' Brother PR655 Embroidery Machine

'''Requires in-person training:''' Peer-to Peer Training Recommened
|width="33%"|
'''Procedure Number'''

UG 141-01, Rev. 1
|width="33%"|
'''Date'''

9/8/2021
|}
[[File:Embroidery.jpg|thumb|Embroidery with the Brother PR655]]
= GENERAL =
{| class="wikitable"
|+
!Feature
!Brother PR655
|-
|Embroidery Area
|12" x 8"
|-
|Needle Count
|6
|-
|Max Speed
|1,000 SPM
|-
|Built-in Designs
|25 + 60 (USB)
|-
|Display Technology
|HD LCD Touchscreen
|}

Brother PR655 Embroidery Machine '''Manual''' : https://download.brother.com/welcome/doch001115/pr655ug01en.pdf

= SAFETY =

This is generally considered a safe machine, however any machine that is used improperly could be hazardous. While sewing always keep the hands clear of the embroidery area.

= PROCEDURE =
'''Design:''' Power on the machine, power button is located on the back right. Touch screen to begin. There are several designs to choose from Check the machine to see what kind of attachments are in place and to make sure all of the needles are threaded. Chose a fabric and stabilizer and attach to a 'Fast Frame' (this is the most convenient and commonly used style of attaching your work piece to the machine) stabilizers are set underneath your fabric of choice (unless you embroidering on a knit fabric those require a special top stabilizer). Setup the design in the machine and embroider.

== My First Embroidery ==
''Embroider your initials''
[[File:Letters .jpg|left|thumb|256x256px|Step 1.4 ]]
This is a predetermined project laid out step-by-step to guide you in practicing base knowledge for this tool.
[[File:Fast frame .jpg|left|thumb|259x259px|Fast Frames Step 2.1 ]]
[[File:My First Project .jpg|left|thumb|263x263px|My First Project ]]
# '''Setting up the design'''
## Turn on the Machine (a little song to welcome you chimes)
##Touch screen to begin
##"The machine will move" message pops (its not lying) move your hands and press "OK"
##Choose one color font (see photo "step 1.4" )
##Choose your letters
##When you are ready to progress to the next step press "SET"
##Notice the size of your piece (you may adjust size or rotation in this screen)
##when your finished editing press "END EDIT"
#'''It's time to set up the work area.'''
##Keeping in mind your project size choose a "fast track" or "fast frame" (they are the same thing, names used interchangeably name) These are the most typical attachment used, and is the most likely to be set up at the machine when you arrive. They are stored over the work bench. (Image 2.1)
##Choose your fabric, a piece of cotton or lightweight canvas should do nicely.
##Find the "stabilizer" this is used on every embroidery project to, well... stabilize the piece while embroidering. It's white and semi opaque. Typically lives under the embroidery work bench or in embroidery storage to the right of the machine.
##Cut both the fabric and stabilizer to fit the chosen fast frame, the stabilizer goes on the top of the fast frame then the fabric on top of that. Attach using binder clips.
##Great! Now its time to attach the fast frame to the Fast Frame "Arm" (if the fast frame receiver is not already there follow the steps in this video: https://youtu.be/S3WEFdFloas?si=fVz_3zm2kZFeg5Cv > second 56) If the frame is attached this should be as simple as loosening the middle knob, putting on the fast frame and settling it into place, and tightening the knob to secure the frame.
##Check the thread color in the first position this will be your color for your first project.
# '''Embroider'''
##Now you're ready to trace out your initials to make sure they fit on your workspace. Use the trace button (white square with a dotted line around it) if the needles hit metal the are likely to break. Change size of your embroidery in previous screens if needed.
##You are ready to embroider. Push the "SEWING" button to advance to the next screen
##Push the lock button on the screen and the arrow below will flash green push that too the machine will begin sewing now!
##Watch your project happen! If you have any trouble along the way check out the troubleshooting section. When it's finished detach everything and trim or tear away your stabilizer.
##Tidy up and done!

== My Second Embroidery ==
''Multicolor preloaded design''
[[File:Thread icon position number .jpg|thumb|Position number image 1.8 ]]
Many steps from the first project will repeat here. New steps are italicized.
#'''Setting up the design'''
## Turn on the Machine (a little song to welcome you chimes)
##Touch screen to begin
##"The machine will move" message pops (its not lying) move your hands and press "OK"
##''Choose a multicolor design'' ''and press "SET"''
##Notice the size of your piece in the middle grey bar (you may adjust size or rotation in this screen)
##When your finished editing press "END EDIT"
##Press "SEWING"
##''When you are in the sewing screen notice the thread icons, the numbers next to them represent thier position on the machine (positions 1-6). (image 1.8) The colors that show up on the screen represent the colors seen in the design. This is obvious but, the colors on the physical thread rack on the back of the machine are the colors that will actually be embroidered in thier corresponding position. We won't go into changing the color of the tread spool icon, only the changing of the physical thread.''
#'''''Changing threads.'''''
##''Cut the string for the previous position one thread just above the spool.''
##''Remove the previous thread and put your chosen thread in its place. Embroidery threads are stored next to the machine on the metal rack.''
##''Without pulling the previous thread too much tie the two tails together. You will be using the previous thread as a guide to pull the new thread through the machine, this is much faster than than threading the machine by hand and works very well, however it is very good to learn the threading process so that you can know when there is a threading issue when troubleshooting. How to thread : https://www.youtube.com/watch?v=Vk_xvHxAVv4''
##''Remove the lowest part of the thread from the needle only. Pull the thread from the bottom and watch it pull all the way through the machine.''
##''Thread the needle leaving a bit of a tail.''
##''Repeat those steps for each thread position.''
#'''It's time to set up the work area.'''
##Keeping in mind your project size choose a "fast track" or "fast frame" (they are the same thing, names used interchangeably name) These are the most typical attachment used, and is the most likely to be set up at the machine when you arrive. They are stored over the work bench. (Image 2.1)
##Choose your fabric, a piece of cotton or lightweight canvas should do nicely.
##Find the "stabilizer" this is used on every embroidery project to, well... stabilize the piece while embroidering. It's white and semi opaque. Typically lives under the embroidery work bench or in embroidery storage to the right of the machine.
##Cut both the fabric and stabilizer to fit the chosen fast frame, the stabilizer goes on the top of the fast frame then the fabric on top of that. Attach using binder clips.
##Great! Now its time to attach the fast frame to the Fast Frame "Arm" (if the fast frame receiver is not already there follow the steps in this video: https://youtu.be/S3WEFdFloas?si=fVz_3zm2kZFeg5Cv > second 56) If the frame is attached this should be as simple as loosening the middle knob, putting on the fast frame and settling it into place, and tightening the knob to secure the frame.
##Check the thread color in the first position this will be your color for your first project.
# '''Embroider'''
##Now you're ready to trace out your initials to make sure they fit on your workspace. Use the trace button (white square with a dotted line around it) if the needles hit metal the are likely to break. Change size of your embroidery in previous screens if needed.
##You are ready to embroider. Push the "SEWING" button to advance to the next screen
##Push the lock button on the screen and the arrow below will flash green push that too the machine will begin sewing now!
##Watch your project happen! If you have any trouble along the way check out the troubleshooting section. When it's finished detach everything and trim or tear away your stabilizer.
##Tidy up and done!

== My Third Embroidery ==
''Custom embroidery digitizing with Inkstitch'' https://www.youtube.com/watch?v=mPaGwjwpzWc

== My Forth Embroidery ==
''Embroidering a hat'' https://www.youtube.com/watch?v=koOPpVUuSC4

= TROUBLESHOOTING =

* Always check that the machine is '''threaded properly''', sewing machines of any kind are notoriously particular when it comes to threading, the tiniest missed detail can lead to problems obvious in the quality of your product. https://www.youtube.com/watch?v=Vk_xvHxAVv4
* Make sure '''tread tail''' is long enough to not pull out of the needle as soon sewing begins
* Make sure the '''bobbin spool''' is seated correctly. There is a magnet in these fancy pre-wound bobbins we buy, the magnet should always face in towards the metal bobbin case. If the spool is not turning in the correct direction or if its not seated well the machine will be embroidering will be interrupted regularly with error messages and your piece will be low quality.
* Check that the '''bobbin spool''' is more than a quarter full, when the bobbin thread gets low it tends to make the machine perform poorly.
* '''Needles''', they can break and dull regularly with use. Check to make sure needles aren't broken. If the needles are dull they can easily cause issues. It's normal to troubleshoot replacing needles if you've already made sure the machine is threaded properly. If you are a normal user of this machine or any sewing machine learning to change the needles is part of what you'll need to know for success. Video tutorial on needle changing: https://www.youtube.com/watch?v=89EveDvM6k0
* The '''tension''' is not this issue as frequently as one might think. Ancel, our area Shop Captain has spent a lot of time understanding and tinkering with tension on this machine to get it into tip-top shape. Adjusting tension dramatically will likely ''not'' yield the desired results. If you are adjusting tension for trouble shooting please do so thoughtfully always being able to return the tension to its original position if that was not in fact the issue.

= <big>REFERENCE</big> =
* Hat attachment video (https://www.youtube.com/watch?v=koOPpVUuSC4)
* Custom embroidery digitizing with Inkstitch (https://www.youtube.com/watch?v=mPaGwjwpzWc)
* Threading, bobbin, and color change Tutorial (https://www.youtube.com/watch?v=Hmb22uwrJZ4)
* Ode to the PR655 and general use (https://www.maggieframes.com/blogs/embroidery-blogs/brother-pr655-ultimate-guide-mastering-your-6-needle-embroidery-machine)
* Glossary of terms (https://kimberbell.com/blogs/thekimberbellablog/machine-embroidery-glossary-of-terms?srsltid=AfmBOopqK-5z8W5BCG8x9qDt5MqvqbmO1LrQKS6Tr2qFypRPuW49Uj0E)
'''END OF THE PROCEDURE'''

Brother-pr655-embroidery-machine

2026-07-09T15:04:13Z

Mwalsh: rdjgj

{|
|width="33%"|
'''Shop Area:''' Textiles

'''Tool:''' Brother PR655 Embroidery Machine

'''Requires in-person training:''' Peer-to Peer Training Recommened
|width="33%"|
'''Procedure Number'''

UG 141-01, Rev. 1
|width="33%"|
'''Date'''

9/8/2021
|}
[[File:Embroidery.jpg|thumb|Embroidery with the Brother PR655]]
= GENERAL =
{| class="wikitable"
|+
!Feature
!Brother PR655
|-
|Embroidery Area
|12" x 8"
|-
|Needle Count
|6
|-
|Max Speed
|1,000 SPM
|-
|Built-in Designs
|25 + 60 (USB)
|-
|Display Technology
|HD LCD Touchscreen
|}

Brother PR655 Embroidery Machine '''Manual''' : https://download.brother.com/welcome/doch001115/pr655ug01en.pdf

= SAFETY =

This is generally considered a safe machine, however any machine that is used improperly could be hazardous. While sewing always keep the hands clear of the embroidery area.

= PROCEDURE =
'''Design:''' Power on the machine, power button is located on the back right. Touch screen to begin. There are several designs to choose from Check the machine to see what kind of attachments are in place and to make sure all of the needles are threaded. Chose a fabric and stabilizer and attach to a 'Fast Frame' (this is the most convenient and commonly used style of attaching your work piece to the machine) stabilizers are set underneath your fabric of choice (unless you embroidering on a knit fabric those require a special top stabilizer). Setup the design in the machine and embroider.

== My First Embroidery ==
''Embroider your initials''
[[File:Letters .jpg|left|thumb|256x256px|Step 1.4 ]]
This is a predetermined project laid out step-by-step to guide you in practicing base knowledge for this tool.
[[File:Fast frame .jpg|left|thumb|259x259px|Fast Frames Step 2.1 ]]
[[File:My First Project .jpg|left|thumb|263x263px|My First Project ]]
# '''Setting up the design'''
## Turn on the Machine (a little song to welcome you chimes)
##Touch screen to begin
##"The machine will move" message pops (its not lying) move your hands and press "OK"
##Choose one color font (see photo "step 1.4" )
##Choose your letters
##When you are ready to progress to the next step press "SET"
##Notice the size of your piece (you may adjust size or rotation in this screen)
##when your finished editing press "END EDIT"
#'''It's time to set up the work area.'''
##Keeping in mind your project size choose a "fast track" or "fast frame" (they are the same thing, names used interchangeably name) These are the most typical attachment used, and is the most likely to be set up at the machine when you arrive. They are stored over the work bench. (Image 2.1)
##Choose your fabric, a piece of cotton or lightweight canvas should do nicely.
##Find the "stabilizer" this is used on every embroidery project to, well... stabilize the piece while embroidering. It's white and semi opaque. Typically lives under the embroidery work bench or in embroidery storage to the right of the machine.
##Cut both the fabric and stabilizer to fit the chosen fast frame, the stabilizer goes on the top of the fast frame then the fabric on top of that. Attach using binder clips.
##Great! Now its time to attach the fast frame to the Fast Frame "Arm" (if the fast frame receiver is not already there follow the steps in this video: https://youtu.be/S3WEFdFloas?si=fVz_3zm2kZFeg5Cv > second 56) If the frame is attached this should be as simple as loosening the middle knob, putting on the fast frame and settling it into place, and tightening the knob to secure the frame.
##Check the thread color in the first position this will be your color for your first project.
# '''Embroider'''
##Now you're ready to trace out your initials to make sure they fit on your workspace. Use the trace button (white square with a dotted line around it) if the needles hit metal the are likely to break. Change size of your embroidery in previous screens if needed.
##You are ready to embroider. Push the "SEWING" button to advance to the next screen
##Push the lock button on the screen and the arrow below will flash green push that too the machine will begin sewing now!
##Watch your project happen! If you have any trouble along the way check out the troubleshooting section. When it's finished detach everything and trim or tear away your stabilizer.
##Tidy up and done!

== My Second Embroidery ==
''Multicolor preloaded design''
[[File:Thread icon position number .jpg|thumb|Position number image 1.8 ]]
Many steps from the first project will repeat here. New steps are italicized.
#'''Setting up the design'''
## Turn on the Machine (a little song to welcome you chimes)
##Touch screen to begin
##"The machine will move" message pops (its not lying) move your hands and press "OK"
##''Choose a multicolor design'' ''and press "SET"''
##Notice the size of your piece in the middle grey bar (you may adjust size or rotation in this screen)
##When your finished editing press "END EDIT"
##Press "SEWING"
##''When you are in the sewing screen notice the thread icons, the numbers next to them represent thier position on the machine (positions 1-6). (image 1.8) The colors that show up on the screen represent the colors seen in the design. This is obvious but, the colors on the physical thread rack on the back of the machine are the colors that will actually be embroidered in thier corresponding position. We won't go into changing the color of the tread spool icon, only the changing of the physical thread.''
#'''''Changing threads.'''''
##''Cut the string for the previous position one thread just above the spool.''
##''Remove the previous thread and put your chosen thread in its place. Embroidery threads are stored next to the machine on the metal rack.''
##''Without pulling the previous thread too much tie the two tails together. You will be using the previous thread as a guide to pull the new thread through the machine, this is much faster than than threading the machine by hand and works very well, however it is very good to learn the threading process so that you can know when there is a threading issue when troubleshooting. How to thread : https://www.youtube.com/watch?v=Vk_xvHxAVv4''
##''Remove the lowest part of the thread from the needle only. Pull the thread from the bottom and watch it pull all the way through the machine.''
##''Thread the needle leaving a bit of a tail.''
##''Repeat those steps for each thread position.''
#'''It's time to set up the work area.'''
##Keeping in mind your project size choose a "fast track" or "fast frame" (they are the same thing, names used interchangeably name) These are the most typical attachment used, and is the most likely to be set up at the machine when you arrive. They are stored over the work bench. (Image 2.1)
##Choose your fabric, a piece of cotton or lightweight canvas should do nicely.
##Find the "stabilizer" this is used on every embroidery project to, well... stabilize the piece while embroidering. It's white and semi opaque. Typically lives under the embroidery work bench or in embroidery storage to the right of the machine.
##Cut both the fabric and stabilizer to fit the chosen fast frame, the stabilizer goes on the top of the fast frame then the fabric on top of that. Attach using binder clips.
##Great! Now its time to attach the fast frame to the Fast Frame "Arm" (if the fast frame receiver is not already there follow the steps in this video: https://youtu.be/S3WEFdFloas?si=fVz_3zm2kZFeg5Cv > second 56) If the frame is attached this should be as simple as loosening the middle knob, putting on the fast frame and settling it into place, and tightening the knob to secure the frame.
##Check the thread color in the first position this will be your color for your first project.
# '''Embroider'''
##Now you're ready to trace out your initials to make sure they fit on your workspace. Use the trace button (white square with a dotted line around it) if the needles hit metal the are likely to break. Change size of your embroidery in previous screens if needed.
##You are ready to embroider. Push the "SEWING" button to advance to the next screen
##Push the lock button on the screen and the arrow below will flash green push that too the machine will begin sewing now!
##Watch your project happen! If you have any trouble along the way check out the troubleshooting section. When it's finished detach everything and trim or tear away your stabilizer.
##Tidy up and done!

== My Third Embroidery ==
''Custom embroidery digitizing with Inkstitch'' https://www.youtube.com/watch?v=mPaGwjwpzWc

== My Forth Embroidery ==
''Embroidering a hat'' https://www.youtube.com/watch?v=koOPpVUuSC4

= TROUBLESHOOTING =

* Always check that the machine is '''threaded properly''', sewing machines of any kind are notoriously particular when it comes to threading, the tiniest missed detail can lead to problems obvious in the quality of your product. https://www.youtube.com/watch?v=Vk_xvHxAVv4
* Make sure '''tread tail''' is long enough to not pull out of the needle as soon sewing begins
* Make sure the '''bobbin spool''' is seated correctly. There is a magnet in these fancy pre-wound bobbins we buy, the magnet should always face in towards the metal bobbin case. If the spool is not turning in the correct direction or if its not seated well the machine will be embroidering will be interrupted regularly with error messages and your piece will be low quality.
* Check that the '''bobbin spool''' is more than a quarter full, when the bobbin thread gets low it tends to make the machine perform poorly.
* '''Needles''', they can break and dull regularly with use. Check to make sure needles aren't broken. If the needles are dull they can easily cause issues. It's normal to troubleshoot replacing needles if you've already made sure the machine is threaded properly. If you are a normal user of this machine or any sewing machine learning to change the needles is part of what you'll need to know for success. Video tutorial on needle changing: https://www.youtube.com/watch?v=89EveDvM6k0
* The '''tension''' is not this issue as frequently as one might think. Ancel, our area Shop Captain has spent a lot of time understanding and tinkering with tension on this machine to get it into tip-top shape. Adjusting tension dramatically will likely ''not'' yield the desired results. If you are adjusting tension for trouble shooting please do so thoughtfully always being able to return the tension to its original position if that was not in fact the issue.

= <big>REFERENCE</big> =
* Hat attachment video (https://www.youtube.com/watch?v=koOPpVUuSC4)
* Custom embroidery digitizing with Inkstitch (https://www.youtube.com/watch?v=mPaGwjwpzWc)
* Threading, bobbin, and color change Tutorial (https://www.youtube.com/watch?v=Hmb22uwrJZ4)
* Ode to the PR655 and general use (https://www.maggieframes.com/blogs/embroidery-blogs/brother-pr655-ultimate-guide-mastering-your-6-needle-embroidery-machine)
* Glossary of terms (https://kimberbell.com/blogs/thekimberbellablog/machine-embroidery-glossary-of-terms?srsltid=AfmBOopqK-5z8W5BCG8x9qDt5MqvqbmO1LrQKS6Tr2qFypRPuW49Uj0E)
'''END OF THE PROCEDURE'''

Brother-pr655-embroidery-machine

2026-07-09T15:02:44Z

Mwalsh: minor

{|
|width="33%"|
'''Shop Area:''' Textiles

'''Tool:''' Brother PR655 Embroidery Machine

'''Requires in-person training:''' Peer-to Peer Training Recommened
|width="33%"|
'''Procedure Number'''

UG 141-01, Rev. 1
|width="33%"|
'''Date'''

9/8/2021
|}
[[File:Embroidery.jpg|thumb|Embroidery with the Brother PR655]]
= GENERAL =
{| class="wikitable"
|+
!Feature
!Brother PR655
|-
|Embroidery Area
|12" x 8"
|-
|Needle Count
|6
|-
|Max Speed
|1,000 SPM
|-
|Built-in Designs
|25 + 60 (USB)
|-
|Display Technology
|HD LCD Touchscreen
|}

Brother PR655 Embroidery Machine '''Manual''' : https://download.brother.com/welcome/doch001115/pr655ug01en.pdf

= SAFETY =

This is generally considered a safe machine, however any machine that is used improperly could be hazardous. While sewing always keep the hands clear of the embroidery area.

= PROCEDURE =
'''Design:''' Power on the machine, power button is located on the back right. Touch screen to begin. There are several designs to choose from Check the machine to see what kind of attachments are in place and to make sure all of the needles are threaded. Chose a fabric and stabilizer and attach to a 'Fast Frame' (this is the most convenient and commonly used style of attaching your work piece to the machine) stabilizers are set underneath your fabric of choice (unless you embroidering on a knit fabric those require a special top stabilizer).

== My First Embroidery ==
''Embroider your initials''
[[File:Letters .jpg|left|thumb|256x256px|Step 1.4 ]]
This is a predetermined project laid out step-by-step to guide you in practicing base knowledge for this tool.
[[File:Fast frame .jpg|left|thumb|259x259px|Fast Frames Step 2.1 ]]
[[File:My First Project .jpg|left|thumb|263x263px|My First Project ]]
# '''Setting up the design'''
## Turn on the Machine (a little song to welcome you chimes)
##Touch screen to begin
##"The machine will move" message pops (its not lying) move your hands and press "OK"
##Choose one color font (see photo "step 1.4" )
##Choose your letters
##When you are ready to progress to the next step press "SET"
##Notice the size of your piece (you may adjust size or rotation in this screen)
##when your finished editing press "END EDIT"
#'''It's time to set up the work area.'''
##Keeping in mind your project size choose a "fast track" or "fast frame" (they are the same thing, names used interchangeably name) These are the most typical attachment used, and is the most likely to be set up at the machine when you arrive. They are stored over the work bench. (Image 2.1)
##Choose your fabric, a piece of cotton or lightweight canvas should do nicely.
##Find the "stabilizer" this is used on every embroidery project to, well... stabilize the piece while embroidering. It's white and semi opaque. Typically lives under the embroidery work bench or in embroidery storage to the right of the machine.
##Cut both the fabric and stabilizer to fit the chosen fast frame, the stabilizer goes on the top of the fast frame then the fabric on top of that. Attach using binder clips.
##Great! Now its time to attach the fast frame to the Fast Frame "Arm" (if the fast frame receiver is not already there follow the steps in this video: https://youtu.be/S3WEFdFloas?si=fVz_3zm2kZFeg5Cv > second 56) If the frame is attached this should be as simple as loosening the middle knob, putting on the fast frame and settling it into place, and tightening the knob to secure the frame.
##Check the thread color in the first position this will be your color for your first project.
# '''Embroider'''
##Now you're ready to trace out your initials to make sure they fit on your workspace. Use the trace button (white square with a dotted line around it) if the needles hit metal the are likely to break. Change size of your embroidery in previous screens if needed.
##You are ready to embroider. Push the "SEWING" button to advance to the next screen
##Push the lock button on the screen and the arrow below will flash green push that too the machine will begin sewing now!
##Watch your project happen! If you have any trouble along the way check out the troubleshooting section. When it's finished detach everything and trim or tear away your stabilizer.
##Tidy up and done!

== My Second Embroidery ==
''Multicolor preloaded design''
[[File:Thread icon position number .jpg|thumb|Position number image 1.8 ]]
Many steps from the first project will repeat here. New steps are italicized.
#'''Setting up the design'''
## Turn on the Machine (a little song to welcome you chimes)
##Touch screen to begin
##"The machine will move" message pops (its not lying) move your hands and press "OK"
##''Choose a multicolor design'' ''and press "SET"''
##Notice the size of your piece in the middle grey bar (you may adjust size or rotation in this screen)
##When your finished editing press "END EDIT"
##Press "SEWING"
##''When you are in the sewing screen notice the thread icons, the numbers next to them represent thier position on the machine (positions 1-6). (image 1.8) The colors that show up on the screen represent the colors seen in the design. This is obvious but, the colors on the physical thread rack on the back of the machine are the colors that will actually be embroidered in thier corresponding position. We won't go into changing the color of the tread spool icon, only the changing of the physical thread.''
#'''''Changing threads.'''''
##''Cut the string for the previous position one thread just above the spool.''
##''Remove the previous thread and put your chosen thread in its place. Embroidery threads are stored next to the machine on the metal rack.''
##''Without pulling the previous thread too much tie the two tails together. You will be using the previous thread as a guide to pull the new thread through the machine, this is much faster than than threading the machine by hand and works very well, however it is very good to learn the threading process so that you can know when there is a threading issue when troubleshooting. How to thread : https://www.youtube.com/watch?v=Vk_xvHxAVv4''
##''Remove the lowest part of the thread from the needle only. Pull the thread from the bottom and watch it pull all the way through the machine.''
##''Thread the needle leaving a bit of a tail.''
##''Repeat those steps for each thread position.''
#'''It's time to set up the work area.'''
##Keeping in mind your project size choose a "fast track" or "fast frame" (they are the same thing, names used interchangeably name) These are the most typical attachment used, and is the most likely to be set up at the machine when you arrive. They are stored over the work bench. (Image 2.1)
##Choose your fabric, a piece of cotton or lightweight canvas should do nicely.
##Find the "stabilizer" this is used on every embroidery project to, well... stabilize the piece while embroidering. It's white and semi opaque. Typically lives under the embroidery work bench or in embroidery storage to the right of the machine.
##Cut both the fabric and stabilizer to fit the chosen fast frame, the stabilizer goes on the top of the fast frame then the fabric on top of that. Attach using binder clips.
##Great! Now its time to attach the fast frame to the Fast Frame "Arm" (if the fast frame receiver is not already there follow the steps in this video: https://youtu.be/S3WEFdFloas?si=fVz_3zm2kZFeg5Cv > second 56) If the frame is attached this should be as simple as loosening the middle knob, putting on the fast frame and settling it into place, and tightening the knob to secure the frame.
##Check the thread color in the first position this will be your color for your first project.
# '''Embroider'''
##Now you're ready to trace out your initials to make sure they fit on your workspace. Use the trace button (white square with a dotted line around it) if the needles hit metal the are likely to break. Change size of your embroidery in previous screens if needed.
##You are ready to embroider. Push the "SEWING" button to advance to the next screen
##Push the lock button on the screen and the arrow below will flash green push that too the machine will begin sewing now!
##Watch your project happen! If you have any trouble along the way check out the troubleshooting section. When it's finished detach everything and trim or tear away your stabilizer.
##Tidy up and done!

== My Third Embroidery ==
''Custom embroidery digitizing with Inkstitch'' https://www.youtube.com/watch?v=mPaGwjwpzWc

== My Forth Embroidery ==
''Embroidering a hat'' https://www.youtube.com/watch?v=koOPpVUuSC4

= TROUBLESHOOTING =

* Always check that the machine is '''threaded properly''', sewing machines of any kind are notoriously particular when it comes to threading, the tiniest missed detail can lead to problems obvious in the quality of your product. https://www.youtube.com/watch?v=Vk_xvHxAVv4
* Make sure '''tread tail''' is long enough to not pull out of the needle as soon sewing begins
* Make sure the '''bobbin spool''' is seated correctly. There is a magnet in these fancy pre-wound bobbins we buy, the magnet should always face in towards the metal bobbin case. If the spool is not turning in the correct direction or if its not seated well the machine will be embroidering will be interrupted regularly with error messages and your piece will be low quality.
* Check that the '''bobbin spool''' is more than a quarter full, when the bobbin thread gets low it tends to make the machine perform poorly.
* '''Needles''', they can break and dull regularly with use. Check to make sure needles aren't broken. If the needles are dull they can easily cause issues. It's normal to troubleshoot replacing needles if you've already made sure the machine is threaded properly. If you are a normal user of this machine or any sewing machine learning to change the needles is part of what you'll need to know for success. Video tutorial on needle changing: https://www.youtube.com/watch?v=89EveDvM6k0
* The '''tension''' is not this issue as frequently as one might think. Ancel, our area Shop Captain has spent a lot of time understanding and tinkering with tension on this machine to get it into tip-top shape. Adjusting tension dramatically will likely ''not'' yield the desired results. If you are adjusting tension for trouble shooting please do so thoughtfully always being able to return the tension to its original position if that was not in fact the issue.

= <big>REFERENCE</big> =
* Hat attachment video (https://www.youtube.com/watch?v=koOPpVUuSC4)
* Custom embroidery digitizing with Inkstitch (https://www.youtube.com/watch?v=mPaGwjwpzWc)
* Threading, bobbin, and color change Tutorial (https://www.youtube.com/watch?v=Hmb22uwrJZ4)
* Ode to the PR655 and general use (https://www.maggieframes.com/blogs/embroidery-blogs/brother-pr655-ultimate-guide-mastering-your-6-needle-embroidery-machine)
* Glossary of terms (https://kimberbell.com/blogs/thekimberbellablog/machine-embroidery-glossary-of-terms?srsltid=AfmBOopqK-5z8W5BCG8x9qDt5MqvqbmO1LrQKS6Tr2qFypRPuW49Uj0E)
'''END OF THE PROCEDURE'''

Brother-pr655-embroidery-machine

2026-07-09T15:01:29Z

Mwalsh: picture

{|
|width="33%"|
'''Shop Area:''' Textiles

'''Tool:''' Brother PR655 Embroidery Machine

'''Requires in-person training:''' Peer-to Peer Training Recommened
|width="33%"|
'''Procedure Number'''

UG 141-01, Rev. 1
|width="33%"|
'''Date'''

9/8/2021
|}
[[File:Embroidery.jpg|thumb|Embroidery with the Brother PR655]]
= GENERAL =
{| class="wikitable"
|+
!Feature
!Brother PR655
|-
|Embroidery Area
|12" x 8"
|-
|Needle Count
|6
|-
|Max Speed
|1,000 SPM
|-
|Built-in Designs
|25 + 60 (USB)
|-
|Display Technology
|HD LCD Touchscreen
|}

Brother PR655 Embroidery Machine '''Manual''' : https://download.brother.com/welcome/doch001115/pr655ug01en.pdf

= SAFETY =

This is generally considered a safe machine, however any machine that is used improperly could be hazardous. It's important to know that when you turn on the machine head will move as the machine reorients it's self to find "home". While sewing always keep the hands clear of the embroidery area.

= PROCEDURE =
'''Design:''' Power on the machine, power button is located on the back right. Touch screen to begin. There are several designs to choose from Check the machine to see what kind of attachments are in place and to make sure all of the needles are threaded. Chose a fabric and stabilizer and attach to a 'Fast Frame' (this is the most convenient and commonly used style of attaching your work piece to the machine) stabilizers are set underneath your fabric of choice (unless you embroidering on a knit fabric those require a special top stabilizer).

== My First Embroidery ==
''Embroider your initials''
[[File:Letters .jpg|left|thumb|256x256px|Step 1.4 ]]
This is a predetermined project laid out step-by-step to guide you in practicing base knowledge for this tool.
[[File:Fast frame .jpg|left|thumb|259x259px|Fast Frames Step 2.1 ]]
[[File:My First Project .jpg|left|thumb|263x263px|My First Project ]]
# '''Setting up the design'''
## Turn on the Machine (a little song to welcome you chimes)
##Touch screen to begin
##"The machine will move" message pops (its not lying) move your hands and press "OK"
##Choose one color font (see photo "step 1.4" )
##Choose your letters
##When you are ready to progress to the next step press "SET"
##Notice the size of your piece (you may adjust size or rotation in this screen)
##when your finished editing press "END EDIT"
#'''It's time to set up the work area.'''
##Keeping in mind your project size choose a "fast track" or "fast frame" (they are the same thing, names used interchangeably name) These are the most typical attachment used, and is the most likely to be set up at the machine when you arrive. They are stored over the work bench. (Image 2.1)
##Choose your fabric, a piece of cotton or lightweight canvas should do nicely.
##Find the "stabilizer" this is used on every embroidery project to, well... stabilize the piece while embroidering. It's white and semi opaque. Typically lives under the embroidery work bench or in embroidery storage to the right of the machine.
##Cut both the fabric and stabilizer to fit the chosen fast frame, the stabilizer goes on the top of the fast frame then the fabric on top of that. Attach using binder clips.
##Great! Now its time to attach the fast frame to the Fast Frame "Arm" (if the fast frame receiver is not already there follow the steps in this video: https://youtu.be/S3WEFdFloas?si=fVz_3zm2kZFeg5Cv > second 56) If the frame is attached this should be as simple as loosening the middle knob, putting on the fast frame and settling it into place, and tightening the knob to secure the frame.
##Check the thread color in the first position this will be your color for your first project.
# '''Embroider'''
##Now you're ready to trace out your initials to make sure they fit on your workspace. Use the trace button (white square with a dotted line around it) if the needles hit metal the are likely to break. Change size of your embroidery in previous screens if needed.
##You are ready to embroider. Push the "SEWING" button to advance to the next screen
##Push the lock button on the screen and the arrow below will flash green push that too the machine will begin sewing now!
##Watch your project happen! If you have any trouble along the way check out the troubleshooting section. When it's finished detach everything and trim or tear away your stabilizer.
##Tidy up and done!

== My Second Embroidery ==
''Multicolor preloaded design''
[[File:Thread icon position number .jpg|thumb|Position number image 1.8 ]]
Many steps from the first project will repeat here. New steps are italicized.
#'''Setting up the design'''
## Turn on the Machine (a little song to welcome you chimes)
##Touch screen to begin
##"The machine will move" message pops (its not lying) move your hands and press "OK"
##''Choose a multicolor design'' ''and press "SET"''
##Notice the size of your piece in the middle grey bar (you may adjust size or rotation in this screen)
##When your finished editing press "END EDIT"
##Press "SEWING"
##''When you are in the sewing screen notice the thread icons, the numbers next to them represent thier position on the machine (positions 1-6). (image 1.8) The colors that show up on the screen represent the colors seen in the design. This is obvious but, the colors on the physical thread rack on the back of the machine are the colors that will actually be embroidered in thier corresponding position. We won't go into changing the color of the tread spool icon, only the changing of the physical thread.''
#'''''Changing threads.'''''
##''Cut the string for the previous position one thread just above the spool.''
##''Remove the previous thread and put your chosen thread in its place. Embroidery threads are stored next to the machine on the metal rack.''
##''Without pulling the previous thread too much tie the two tails together. You will be using the previous thread as a guide to pull the new thread through the machine, this is much faster than than threading the machine by hand and works very well, however it is very good to learn the threading process so that you can know when there is a threading issue when troubleshooting. How to thread : https://www.youtube.com/watch?v=Vk_xvHxAVv4''
##''Remove the lowest part of the thread from the needle only. Pull the thread from the bottom and watch it pull all the way through the machine.''
##''Thread the needle leaving a bit of a tail.''
##''Repeat those steps for each thread position.''
#'''It's time to set up the work area.'''
##Keeping in mind your project size choose a "fast track" or "fast frame" (they are the same thing, names used interchangeably name) These are the most typical attachment used, and is the most likely to be set up at the machine when you arrive. They are stored over the work bench. (Image 2.1)
##Choose your fabric, a piece of cotton or lightweight canvas should do nicely.
##Find the "stabilizer" this is used on every embroidery project to, well... stabilize the piece while embroidering. It's white and semi opaque. Typically lives under the embroidery work bench or in embroidery storage to the right of the machine.
##Cut both the fabric and stabilizer to fit the chosen fast frame, the stabilizer goes on the top of the fast frame then the fabric on top of that. Attach using binder clips.
##Great! Now its time to attach the fast frame to the Fast Frame "Arm" (if the fast frame receiver is not already there follow the steps in this video: https://youtu.be/S3WEFdFloas?si=fVz_3zm2kZFeg5Cv > second 56) If the frame is attached this should be as simple as loosening the middle knob, putting on the fast frame and settling it into place, and tightening the knob to secure the frame.
##Check the thread color in the first position this will be your color for your first project.
# '''Embroider'''
##Now you're ready to trace out your initials to make sure they fit on your workspace. Use the trace button (white square with a dotted line around it) if the needles hit metal the are likely to break. Change size of your embroidery in previous screens if needed.
##You are ready to embroider. Push the "SEWING" button to advance to the next screen
##Push the lock button on the screen and the arrow below will flash green push that too the machine will begin sewing now!
##Watch your project happen! If you have any trouble along the way check out the troubleshooting section. When it's finished detach everything and trim or tear away your stabilizer.
##Tidy up and done!

== My Third Embroidery ==
''Custom embroidery digitizing with Inkstitch'' https://www.youtube.com/watch?v=mPaGwjwpzWc

== My Forth Embroidery ==
''Embroidering a hat'' https://www.youtube.com/watch?v=koOPpVUuSC4

= TROUBLESHOOTING =

* Always check that the machine is '''threaded properly''', sewing machines of any kind are notoriously particular when it comes to threading, the tiniest missed detail can lead to problems obvious in the quality of your product. https://www.youtube.com/watch?v=Vk_xvHxAVv4
* Make sure '''tread tail''' is long enough to not pull out of the needle as soon sewing begins
* Make sure the '''bobbin spool''' is seated correctly. There is a magnet in these fancy pre-wound bobbins we buy, the magnet should always face in towards the metal bobbin case. If the spool is not turning in the correct direction or if its not seated well the machine will be embroidering will be interrupted regularly with error messages and your piece will be low quality.
* Check that the '''bobbin spool''' is more than a quarter full, when the bobbin thread gets low it tends to make the machine perform poorly.
* '''Needles''', they can break and dull regularly with use. Check to make sure needles aren't broken. If the needles are dull they can easily cause issues. It's normal to troubleshoot replacing needles if you've already made sure the machine is threaded properly. If you are a normal user of this machine or any sewing machine learning to change the needles is part of what you'll need to know for success. Video tutorial on needle changing: https://www.youtube.com/watch?v=89EveDvM6k0
* The '''tension''' is not this issue as frequently as one might think. Ancel, our area Shop Captain has spent a lot of time understanding and tinkering with tension on this machine to get it into tip-top shape. Adjusting tension dramatically will likely ''not'' yield the desired results. If you are adjusting tension for trouble shooting please do so thoughtfully always being able to return the tension to its original position if that was not in fact the issue.

= <big>REFERENCE</big> =
* Hat attachment video (https://www.youtube.com/watch?v=koOPpVUuSC4)
* Custom embroidery digitizing with Inkstitch (https://www.youtube.com/watch?v=mPaGwjwpzWc)
* Threading, bobbin, and color change Tutorial (https://www.youtube.com/watch?v=Hmb22uwrJZ4)
* Ode to the PR655 and general use (https://www.maggieframes.com/blogs/embroidery-blogs/brother-pr655-ultimate-guide-mastering-your-6-needle-embroidery-machine)
* Glossary of terms (https://kimberbell.com/blogs/thekimberbellablog/machine-embroidery-glossary-of-terms?srsltid=AfmBOopqK-5z8W5BCG8x9qDt5MqvqbmO1LrQKS6Tr2qFypRPuW49Uj0E)
'''END OF THE PROCEDURE'''

Brother-pr655-embroidery-machine

2026-07-09T14:54:51Z

Mwalsh: sections 3, 4

{|
|width="33%"|
'''Shop Area:''' Textiles

'''Tool:''' Brother PR655 Embroidery Machine

'''Requires in-person training:''' Peer-to Peer Training Recommened
|width="33%"|
'''Procedure Number'''

UG 141-01, Rev. 1
|width="33%"|
'''Date'''

9/8/2021
|}
[[File:Embroidery.jpg|thumb|Embroidery with the Brother PR655|left]]
= GENERAL =
{| class="wikitable"
|+
!Feature
!Brother PR655
|-
|Embroidery Area
|12" x 8"
|-
|Needle Count
|6
|-
|Max Speed
|1,000 SPM
|-
|Built-in Designs
|25 + 60 (USB)
|-
|Display Technology
|HD LCD Touchscreen
|}

Brother PR655 Embroidery Machine '''Manual''' : https://download.brother.com/welcome/doch001115/pr655ug01en.pdf

= SAFETY =

This is generally considered a safe machine, however any machine that is used improperly could be hazardous. It's important to know that when you turn on the machine head will move as the machine reorients it's self to find "home". While sewing always keep the hands clear of the embroidery area.

= PROCEDURE =
'''Design:''' Power on the machine, power button is located on the back right. Touch screen to begin. There are several designs to choose from Check the machine to see what kind of attachments are in place and to make sure all of the needles are threaded. Chose a fabric and stabilizer and attach to a 'Fast Frame' (this is the most convenient and commonly used style of attaching your work piece to the machine) stabilizers are set underneath your fabric of choice (unless you embroidering on a knit fabric those require a special top stabilizer).

== My First Embroidery ==
''Embroider your initials''
[[File:Letters .jpg|left|thumb|256x256px|Step 1.4 ]]
This is a predetermined project laid out step-by-step to guide you in practicing base knowledge for this tool.
[[File:Fast frame .jpg|left|thumb|259x259px|Fast Frames Step 2.1 ]]
[[File:My First Project .jpg|left|thumb|263x263px|My First Project ]]
# '''Setting up the design'''
## Turn on the Machine (a little song to welcome you chimes)
##Touch screen to begin
##"The machine will move" message pops (its not lying) move your hands and press "OK"
##Choose one color font (see photo "step 1.4" )
##Choose your letters
##When you are ready to progress to the next step press "SET"
##Notice the size of your piece (you may adjust size or rotation in this screen)
##when your finished editing press "END EDIT"
#'''It's time to set up the work area.'''
##Keeping in mind your project size choose a "fast track" or "fast frame" (they are the same thing, names used interchangeably name) These are the most typical attachment used, and is the most likely to be set up at the machine when you arrive. They are stored over the work bench. (Image 2.1)
##Choose your fabric, a piece of cotton or lightweight canvas should do nicely.
##Find the "stabilizer" this is used on every embroidery project to, well... stabilize the piece while embroidering. It's white and semi opaque. Typically lives under the embroidery work bench or in embroidery storage to the right of the machine.
##Cut both the fabric and stabilizer to fit the chosen fast frame, the stabilizer goes on the top of the fast frame then the fabric on top of that. Attach using binder clips.
##Great! Now its time to attach the fast frame to the Fast Frame "Arm" (if the fast frame receiver is not already there follow the steps in this video: https://youtu.be/S3WEFdFloas?si=fVz_3zm2kZFeg5Cv > second 56) If the frame is attached this should be as simple as loosening the middle knob, putting on the fast frame and settling it into place, and tightening the knob to secure the frame.
##Check the thread color in the first position this will be your color for your first project.
# '''Embroider'''
##Now you're ready to trace out your initials to make sure they fit on your workspace. Use the trace button (white square with a dotted line around it) if the needles hit metal the are likely to break. Change size of your embroidery in previous screens if needed.
##You are ready to embroider. Push the "SEWING" button to advance to the next screen
##Push the lock button on the screen and the arrow below will flash green push that too the machine will begin sewing now!
##Watch your project happen! If you have any trouble along the way check out the troubleshooting section. When it's finished detach everything and trim or tear away your stabilizer.
##Tidy up and done!

== My Second Embroidery ==
''Multicolor preloaded design''
[[File:Thread icon position number .jpg|thumb|Position number image 1.8 ]]
Many steps from the first project will repeat here. New steps are italicized.
#'''Setting up the design'''
## Turn on the Machine (a little song to welcome you chimes)
##Touch screen to begin
##"The machine will move" message pops (its not lying) move your hands and press "OK"
##''Choose a multicolor design'' ''and press "SET"''
##Notice the size of your piece in the middle grey bar (you may adjust size or rotation in this screen)
##When your finished editing press "END EDIT"
##Press "SEWING"
##''When you are in the sewing screen notice the thread icons, the numbers next to them represent thier position on the machine (positions 1-6). (image 1.8) The colors that show up on the screen represent the colors seen in the design. This is obvious but, the colors on the physical thread rack on the back of the machine are the colors that will actually be embroidered in thier corresponding position. We won't go into changing the color of the tread spool icon, only the changing of the physical thread.''
#'''''Changing threads.'''''
##''Cut the string for the previous position one thread just above the spool.''
##''Remove the previous thread and put your chosen thread in its place. Embroidery threads are stored next to the machine on the metal rack.''
##''Without pulling the previous thread too much tie the two tails together. You will be using the previous thread as a guide to pull the new thread through the machine, this is much faster than than threading the machine by hand and works very well, however it is very good to learn the threading process so that you can know when there is a threading issue when troubleshooting. How to thread : https://www.youtube.com/watch?v=Vk_xvHxAVv4''
##''Remove the lowest part of the thread from the needle only. Pull the thread from the bottom and watch it pull all the way through the machine.''
##''Thread the needle leaving a bit of a tail.''
##''Repeat those steps for each thread position.''
#'''It's time to set up the work area.'''
##Keeping in mind your project size choose a "fast track" or "fast frame" (they are the same thing, names used interchangeably name) These are the most typical attachment used, and is the most likely to be set up at the machine when you arrive. They are stored over the work bench. (Image 2.1)
##Choose your fabric, a piece of cotton or lightweight canvas should do nicely.
##Find the "stabilizer" this is used on every embroidery project to, well... stabilize the piece while embroidering. It's white and semi opaque. Typically lives under the embroidery work bench or in embroidery storage to the right of the machine.
##Cut both the fabric and stabilizer to fit the chosen fast frame, the stabilizer goes on the top of the fast frame then the fabric on top of that. Attach using binder clips.
##Great! Now its time to attach the fast frame to the Fast Frame "Arm" (if the fast frame receiver is not already there follow the steps in this video: https://youtu.be/S3WEFdFloas?si=fVz_3zm2kZFeg5Cv > second 56) If the frame is attached this should be as simple as loosening the middle knob, putting on the fast frame and settling it into place, and tightening the knob to secure the frame.
##Check the thread color in the first position this will be your color for your first project.
# '''Embroider'''
##Now you're ready to trace out your initials to make sure they fit on your workspace. Use the trace button (white square with a dotted line around it) if the needles hit metal the are likely to break. Change size of your embroidery in previous screens if needed.
##You are ready to embroider. Push the "SEWING" button to advance to the next screen
##Push the lock button on the screen and the arrow below will flash green push that too the machine will begin sewing now!
##Watch your project happen! If you have any trouble along the way check out the troubleshooting section. When it's finished detach everything and trim or tear away your stabilizer.
##Tidy up and done!

== My Third Embroidery ==
''Custom embroidery digitizing with Inkstitch'' https://www.youtube.com/watch?v=mPaGwjwpzWc

== My Forth Embroidery ==
''Embroidering a hat'' https://www.youtube.com/watch?v=koOPpVUuSC4

= TROUBLESHOOTING =

* Always check that the machine is '''threaded properly''', sewing machines of any kind are notoriously particular when it comes to threading, the tiniest missed detail can lead to problems obvious in the quality of your product. https://www.youtube.com/watch?v=Vk_xvHxAVv4
* Make sure '''tread tail''' is long enough to not pull out of the needle as soon sewing begins
* Make sure the '''bobbin spool''' is seated correctly. There is a magnet in these fancy pre-wound bobbins we buy, the magnet should always face in towards the metal bobbin case. If the spool is not turning in the correct direction or if its not seated well the machine will be embroidering will be interrupted regularly with error messages and your piece will be low quality.
* Check that the '''bobbin spool''' is more than a quarter full, when the bobbin thread gets low it tends to make the machine perform poorly.
* '''Needles''', they can break and dull regularly with use. Check to make sure needles aren't broken. If the needles are dull they can easily cause issues. It's normal to troubleshoot replacing needles if you've already made sure the machine is threaded properly. If you are a normal user of this machine or any sewing machine learning to change the needles is part of what you'll need to know for success. Video tutorial on needle changing: https://www.youtube.com/watch?v=89EveDvM6k0
* The '''tension''' is not this issue as frequently as one might think. Ancel, our area Shop Captain has spent a lot of time understanding and tinkering with tension on this machine to get it into tip-top shape. Adjusting tension dramatically will likely ''not'' yield the desired results. If you are adjusting tension for trouble shooting please do so thoughtfully always being able to return the tension to its original position if that was not in fact the issue.

= <big>REFERENCE</big> =
* Hat attachment video (https://www.youtube.com/watch?v=koOPpVUuSC4)
* Custom embroidery digitizing with Inkstitch (https://www.youtube.com/watch?v=mPaGwjwpzWc)
* Threading, bobbin, and color change Tutorial (https://www.youtube.com/watch?v=Hmb22uwrJZ4)
* Ode to the PR655 and general use (https://www.maggieframes.com/blogs/embroidery-blogs/brother-pr655-ultimate-guide-mastering-your-6-needle-embroidery-machine)
* Glossary of terms (https://kimberbell.com/blogs/thekimberbellablog/machine-embroidery-glossary-of-terms?srsltid=AfmBOopqK-5z8W5BCG8x9qDt5MqvqbmO1LrQKS6Tr2qFypRPuW49Uj0E)
'''END OF THE PROCEDURE'''

Brother-pr655-embroidery-machine

2026-07-09T14:49:12Z

Mwalsh: second project

{|
|width="33%"|
'''Shop Area:''' Textiles

'''Tool:''' Brother PR655 Embroidery Machine

'''Requires in-person training:''' Peer-to Peer Training Recommened
|width="33%"|
'''Procedure Number'''

UG 141-01, Rev. 1
|width="33%"|
'''Date'''

9/8/2021
|}
[[File:Embroidery.jpg|thumb|Embroidery with the Brother PR655|left]]
= GENERAL =
{| class="wikitable"
|+
!Feature
!Brother PR655
|-
|Embroidery Area
|12" x 8"
|-
|Needle Count
|6
|-
|Max Speed
|1,000 SPM
|-
|Built-in Designs
|25 + 60 (USB)
|-
|Display Technology
|HD LCD Touchscreen
|}

Brother PR655 Embroidery Machine '''Manual''' : https://download.brother.com/welcome/doch001115/pr655ug01en.pdf

= SAFETY =

This is generally considered a safe machine, however any machine that is used improperly could be hazardous. It's important to know that when you turn on the machine head will move as the machine reorients it's self to find "home". While sewing always keep the hands clear of the embroidery area.

= PROCEDURE =
'''Design:''' Power on the machine, power button is located on the back right. Touch screen to begin. There are several designs to choose from Check the machine to see what kind of attachments are in place and to make sure all of the needles are threaded. Chose a fabric and stabilizer and attach to a 'Fast Frame' (this is the most convenient and commonly used style of attaching your work piece to the machine) stabilizers are set underneath your fabric of choice (unless you embroidering on a knit fabric those require a special top stabilizer).

== My First Embroidery ==
''Embroider your initials''
[[File:Letters .jpg|left|thumb|256x256px|Step 1.4 ]]
This is a predetermined project laid out step-by-step to guide you in practicing base knowledge for this tool.
[[File:Fast frame .jpg|left|thumb|259x259px|Fast Frames Step 2.1 ]]
[[File:My First Project .jpg|left|thumb|263x263px|My First Project ]]
# '''Setting up the design'''
## Turn on the Machine (a little song to welcome you chimes)
##Touch screen to begin
##"The machine will move" message pops (its not lying) move your hands and press "OK"
##Choose one color font (see photo "step 1.4" )
##Choose your letters
##When you are ready to progress to the next step press "SET"
##Notice the size of your piece (you may adjust size or rotation in this screen)
##when your finished editing press "END EDIT"
#'''It's time to set up the work area.'''
##Keeping in mind your project size choose a "fast track" or "fast frame" (they are the same thing, names used interchangeably name) These are the most typical attachment used, and is the most likely to be set up at the machine when you arrive. They are stored over the work bench. (Image 2.1)
##Choose your fabric, a piece of cotton or lightweight canvas should do nicely.
##Find the "stabilizer" this is used on every embroidery project to, well... stabilize the piece while embroidering. It's white and semi opaque. Typically lives under the embroidery work bench or in embroidery storage to the right of the machine.
##Cut both the fabric and stabilizer to fit the chosen fast frame, the stabilizer goes on the top of the fast frame then the fabric on top of that. Attach using binder clips.
##Great! Now its time to attach the fast frame to the Fast Frame "Arm" (if the fast frame receiver is not already there follow the steps in this video: https://youtu.be/S3WEFdFloas?si=fVz_3zm2kZFeg5Cv > second 56) If the frame is attached this should be as simple as loosening the middle knob, putting on the fast frame and settling it into place, and tightening the knob to secure the frame.
##Check the thread color in the first position this will be your color for your first project.
# '''Embroider'''
##Now you're ready to trace out your initials to make sure they fit on your workspace. Use the trace button (white square with a dotted line around it) if the needles hit metal the are likely to break. Change size of your embroidery in previous screens if needed.
##You are ready to embroider. Push the "SEWING" button to advance to the next screen
##Push the lock button on the screen and the arrow below will flash green push that too the machine will begin sewing now!
##Watch your project happen! If you have any trouble along the way check out the troubleshooting section. When it's finished detach everything and trim or tear away your stabilizer.
##Tidy up and done!

== My Second Embroidery ==
''Multicolor preloaded design''
[[File:Thread icon position number .jpg|thumb|Position number image 1.8 ]]
Many steps from the first project will repeat here. New steps are italicized.
#'''Setting up the design'''
## Turn on the Machine (a little song to welcome you chimes)
##Touch screen to begin
##"The machine will move" message pops (its not lying) move your hands and press "OK"
##''Choose a multicolor design'' ''and press "SET"''
##Notice the size of your piece in the middle grey bar (you may adjust size or rotation in this screen)
##When your finished editing press "END EDIT"
##Press "SEWING"
##''When you are in the sewing screen notice the thread icons, the numbers next to them represent thier position on the machine (positions 1-6). (image 1.8) The colors that show up on the screen represent the colors seen in the design. This is obvious but, the colors on the physical thread rack on the back of the machine are the colors that will actually be embroidered in thier corresponding position. We won't go into changing the color of the tread spool icon, only the changing of the physical thread.''
#'''''Changing threads.'''''
##''Cut the string for the previous position one thread just above the spool.''
##''Remove the previous thread and put your chosen thread in its place. Embroidery threads are stored next to the machine on the metal rack.''
##''Without pulling the previous thread too much tie the two tails together. You will be using the previous thread as a guide to pull the new thread through the machine, this is much faster than than threading the machine by hand and works very well, however it is very good to learn the threading process so that you can know when there is a threading issue when troubleshooting. How to thread : https://www.youtube.com/watch?v=Vk_xvHxAVv4''
##''Remove the lowest part of the thread from the needle only. Pull the thread from the bottom and watch it pull all the way through the machine.''
##''Thread the needle leaving a bit of a tail.''
##''Repeat those steps for each thread position.''
#'''It's time to set up the work area.'''
##Keeping in mind your project size choose a "fast track" or "fast frame" (they are the same thing, names used interchangeably name) These are the most typical attachment used, and is the most likely to be set up at the machine when you arrive. They are stored over the work bench. (Image 2.1)
##Choose your fabric, a piece of cotton or lightweight canvas should do nicely.
##Find the "stabilizer" this is used on every embroidery project to, well... stabilize the piece while embroidering. It's white and semi opaque. Typically lives under the embroidery work bench or in embroidery storage to the right of the machine.
##Cut both the fabric and stabilizer to fit the chosen fast frame, the stabilizer goes on the top of the fast frame then the fabric on top of that. Attach using binder clips.
##Great! Now its time to attach the fast frame to the Fast Frame "Arm" (if the fast frame receiver is not already there follow the steps in this video: https://youtu.be/S3WEFdFloas?si=fVz_3zm2kZFeg5Cv > second 56) If the frame is attached this should be as simple as loosening the middle knob, putting on the fast frame and settling it into place, and tightening the knob to secure the frame.
##Check the thread color in the first position this will be your color for your first project.
# '''Embroider'''
##Now you're ready to trace out your initials to make sure they fit on your workspace. Use the trace button (white square with a dotted line around it) if the needles hit metal the are likely to break. Change size of your embroidery in previous screens if needed.
##You are ready to embroider. Push the "SEWING" button to advance to the next screen
##Push the lock button on the screen and the arrow below will flash green push that too the machine will begin sewing now!
##Watch your project happen! If you have any trouble along the way check out the troubleshooting section. When it's finished detach everything and trim or tear away your stabilizer.
##Tidy up and done!

== My Third Embroidery ==

== My Forth Embroidery ==

= Attachments =

= TROUBLESHOOTING =

* Always check that the machine is '''threaded properly''', sewing machines of any kind are notoriously particular when it comes to threading, the tiniest missed detail can lead to problems obvious in the quality of your product. https://www.youtube.com/watch?v=Vk_xvHxAVv4
* Make sure '''tread tail''' is long enough to not pull out of the needle as soon sewing begins
* Make sure the '''bobbin spool''' is seated correctly. There is a magnet in these fancy pre-wound bobbins we buy, the magnet should always face in towards the metal bobbin case. If the spool is not turning in the correct direction or if its not seated well the machine will be embroidering will be interrupted regularly with error messages and your piece will be low quality.
* Check that the '''bobbin spool''' is more than a quarter full, when the bobbin thread gets low it tends to make the machine perform poorly.
* '''Needles''', they can break and dull regularly with use. Check to make sure needles aren't broken. If the needles are dull they can easily cause issues. It's normal to troubleshoot replacing needles if you've already made sure the machine is threaded properly. If you are a normal user of this machine or any sewing machine learning to change the needles is part of what you'll need to know for success. Video tutorial on needle changing: https://www.youtube.com/watch?v=89EveDvM6k0
* The '''tension''' is not this issue as frequently as one might think. Ancel, our area Shop Captain has spent a lot of time understanding and tinkering with tension on this machine to get it into tip-top shape. Adjusting tension dramatically will likely ''not'' yield the desired results. If you are adjusting tension for trouble shooting please do so thoughtfully always being able to return the tension to its original position if that was not in fact the issue.

= MAINTENANCE =

== <big>REFERENCE</big> ==
* Hat attachment video (https://www.youtube.com/watch?v=koOPpVUuSC4)
* Custom embroidery digitizing with Inkstitch (https://www.youtube.com/watch?v=mPaGwjwpzWc)
* Threading, bobbin, and color change Tutorial (https://www.youtube.com/watch?v=Hmb22uwrJZ4)
* Ode to the PR655 and general use (https://www.maggieframes.com/blogs/embroidery-blogs/brother-pr655-ultimate-guide-mastering-your-6-needle-embroidery-machine)
* Glossary of terms (https://kimberbell.com/blogs/thekimberbellablog/machine-embroidery-glossary-of-terms?srsltid=AfmBOopqK-5z8W5BCG8x9qDt5MqvqbmO1LrQKS6Tr2qFypRPuW49Uj0E)
'''END OF THE PROCEDURE'''

File:Thread icon position number .jpg

2026-07-09T14:47:09Z

Mwalsh:

fkj

Brother-pr655-embroidery-machine

2026-06-25T15:06:06Z

Mwalsh:

Brother-pr655-embroidery-machine

2026-06-24T15:45:24Z

Mwalsh: adding pictures

File:Fast frame .jpg

2026-06-24T15:42:14Z

Mwalsh:

fast frame

File:My First Project .jpg

2026-06-24T14:45:20Z

Mwalsh:

My First Project

Brother-pr655-embroidery-machine

2026-06-23T21:15:49Z

Mwalsh: project one

File:Letters .jpg

2026-06-23T19:49:44Z

Mwalsh:

letters

Brother-pr655-embroidery-machine

2026-06-18T16:39:22Z

Mwalsh: instructions

Brother-pr655-embroidery-machine

2026-06-17T15:11:36Z

Mwalsh: Troubleshooting

Brother-pr655-embroidery-machine

2026-06-17T14:07:14Z

Mwalsh: adding My first Embroidery

Brother-pr655-embroidery-machine

2026-06-16T19:07:26Z

Mwalsh: word edits

Brother-pr655-embroidery-machine

2026-06-16T19:04:35Z

Mwalsh: /* SAFETY */

{|
|width="33%"|
'''Shop Area:''' Textiles

'''Tool:''' Brother PR655 Embroidery Machine

'''Requires in-person training:''' Yes
|width="33%"|
'''Procedure Number'''

UG 141-01, Rev. 1
|width="33%"|
'''Date'''

9/8/2021
|}
[[File:Embroidery.jpg|thumb|Embroidery with the Brother PR655]]

= GENERAL =
Here is the manual to the User tool Guided via the Brother Website: https://download.brother.com/welcome/doch001115/pr655ug01en.pdf

= SAFETY =

This is generally considered a safe machine, however any machine that is used improperly could be hazardous. It's important to know that when you turn on the machine head will move as the machine reorients it's self to find "home". While sewing please keep the hands clear of the sewing embroidery area.

= REFERENCE =
* Hat attachment video (https://www.youtube.com/watch?v=koOPpVUuSC4)
* Custom embroidery digitizing with Inkstitch (https://www.youtube.com/watch?v=mPaGwjwpzWc)
* Threading, bobbin, and color change Tutorial (https://www.youtube.com/watch?v=Hmb22uwrJZ4)

= PROCEDURE =

= TROUBLESHOOTING =

'''END OF THE PROCEDURE'''

File:Embroidery.jpg

2026-06-16T19:03:13Z

Mwalsh:

Embroidery at with the Brother Pr655

File:Pin.jpg

2026-04-22T17:11:22Z

Mwalsh:

Main Page

2026-04-22T17:10:11Z

Mwalsh: added link

==[[design_files|Design Files]]==
==[[Forms|Forms]]==
==[[Policies|Policies]]==
==[[Tool-User-Guides|Tool User Guides]]==
==[[Tool_Trainer_Checklists|Tool Trainer Checklists]]==

==[[Tool_Maintenance_Guides|Tool Maintenance Guides]]==

[https://vector-space.org/wiki/Membership_Resources?veaction=edit Membership Resources]
== Getting started ==
* [https://www.mediawiki.org/wiki/Special:MyLanguage/Manual:Configuration_settings Configuration settings list]
* [https://www.mediawiki.org/wiki/Special:MyLanguage/Manual:FAQ MediaWiki FAQ]
* [https://lists.wikimedia.org/mailman/listinfo/mediawiki-announce MediaWiki release mailing list]
* [https://www.mediawiki.org/wiki/Special:MyLanguage/Localisation#Translation_resources Localise MediaWiki for your language]
* [https://www.mediawiki.org/wiki/Special:MyLanguage/Manual:Combating_spam Learn how to combat spam on your wiki]

Membership Resources

2026-04-22T17:09:11Z

Mwalsh: added link

Membership Resources

2026-04-22T17:03:49Z

Mwalsh: description

File:Member Handbook .jpg

2026-04-22T16:58:26Z

Mwalsh:

Member Handbook

Main Page

2026-04-22T16:53:32Z

Mwalsh: I deleted a heading i tried to add earlier that didn't come out right

==[[design_files|Design Files]]==
==[[Forms|Forms]]==
==[[Policies|Policies]]==
==[[Tool-User-Guides|Tool User Guides]]==
==[[Tool_Trainer_Checklists|Tool Trainer Checklists]]==

==[[Tool_Maintenance_Guides|Tool Maintenance Guides]]==
== Getting started ==
* [https://www.mediawiki.org/wiki/Special:MyLanguage/Manual:Configuration_settings Configuration settings list]
* [https://www.mediawiki.org/wiki/Special:MyLanguage/Manual:FAQ MediaWiki FAQ]
* [https://lists.wikimedia.org/mailman/listinfo/mediawiki-announce MediaWiki release mailing list]
* [https://www.mediawiki.org/wiki/Special:MyLanguage/Localisation#Translation_resources Localise MediaWiki for your language]
* [https://www.mediawiki.org/wiki/Special:MyLanguage/Manual:Combating_spam Learn how to combat spam on your wiki]

Membership Resources

2026-04-22T16:30:25Z

Mwalsh: I started creating a landing page for membership

Main Page

2026-04-22T16:18:19Z

Mwalsh: I hoping to add a link to the main page but maybe failing miserably

==[[design_files|Design Files]]==
==[[Forms|Forms]]==
==[[Policies|Policies]]==
==[[Tool-User-Guides|Tool User Guides]]==
==[[Tool_Trainer_Checklists|Tool Trainer Checklists]]==

==[[Tool_Maintenance_Guides|Tool Maintenance Guides]]==

Membership Resources
== Getting started ==
* [https://www.mediawiki.org/wiki/Special:MyLanguage/Manual:Configuration_settings Configuration settings list]
* [https://www.mediawiki.org/wiki/Special:MyLanguage/Manual:FAQ MediaWiki FAQ]
* [https://lists.wikimedia.org/mailman/listinfo/mediawiki-announce MediaWiki release mailing list]
* [https://www.mediawiki.org/wiki/Special:MyLanguage/Localisation#Translation_resources Localise MediaWiki for your language]
* [https://www.mediawiki.org/wiki/Special:MyLanguage/Manual:Combating_spam Learn how to combat spam on your wiki]